Whirlpool Ultimate Care II GSW9650LW Top Load Washer - Page 2 - Answered Questions & Fixed issues

sounds like the teeth on the timer are going. Some washers however do have a "rest" period to allow the transmission to cool down. give the washer a couple of moments before forcing the dial.

Hi

If your washer won't drain, check these:
It spins, but doesn't pump If your washer spins but doesn't pump the water out, the drain line is probably clogged. In many washers, a small sock or other piece of clothing can get between the clothes tub and the outer tub that holds the water. If the clothing gets between the tubs, it may then get into the drain hose that's attached to the pump--or even into the pump itself. If it's in the pump, you need to remove the hoses from the pump and pull the item out.

To remove the sock from the outer tub port, open the washer's main access panel and remove the large-diameter rubber hose that connects the pump to the bottom of the outer tub. Then, using needle-nose pliers, try to grab and remove the clothing through the port.

Sometimes you can't remove the stuck clothing from below. Then you have to remove the agitator, top of the outer drum shield, and inner clothes tub. This isn't easy to do--and you may need special tools--so you might be happier getting a qualified appliance repair technician to do the job.

If the drain line isn't plugged, the problem may be with your pump. Even if the pump appears to be turning, the internal impeller may be broken. If so, you need to replace the pump.

It doesn't spin or pump If your washer doesn't spin or pump water out but the motor is running, your washer probably has a frozen pump pulley. If so, you need to replace the pump. To check the pulley, remove the pump from the washer and try to rotate the pulley manually. If it doesn't turn freely--if it's frozen or stiff--replace it.

It pumps, but the water returns If the water that pumps out of the machine goes back into the machine after the spin cycle, your washer may be siphoning the water from a laundry tub that has a slow drain, back into the washer. The usual remedy for this is to improve the draining of the laundry tub. (Is something stuck in the drain?) Also, check for these problems:

• If the drain hose reaches more than about 4 inches into the laundry tub, cut off the excess.
  
  
• If your drain hose is lower than the washer's cabinet, install an air gap/siphon break assembly.

Please do rate the solution as FixYa and revert for further assistance.

Thanks
Rylee

YOU'LL HAVE TO GET INTO THE BACK OF IT AND CHECK FOR POWER AT THE CONNECTIONS OF THE WATER INLET VALVE CONNECTIONS WITH THE TIMER AT THE START OF A CYCLE IF NO POWER THEN I THINK YOUR TIMER IS BAD, IF YOU HAVE POWER THEN REPLACE THE WATER INLET VALVE COMPONENT

This sounds like the imbalanced load alarm. This can occur with large heavy loads like blankets, bedding, lots of diapers (cloth), jeans etc. The best solution is to wash lighter loads and not overload the machine. If overloading continues, the machine could be damaged.

Upper end goes to the water level control, lower hooks into the right side of the tub, between the tub and cabinet. Hope this helps!

ck drain hose end of hose should be at least 30-36 inches from floor also end of hose needs to fit loosely in standpipe ..if drainhose is too tight siphoning will occur

you will need to replace fill valve where hoses connect probably has sand in valve especially if screens have been removed remove screws in rear of console lift and roll console back disconnect wire to lid switch remove clips om right and left rear corners cabinet lifts off disconnect hoses and wires 1 screw usually holds valve in postion

Your pump is probably leaking. It's mounted right at the front of the cabinet to the motor. It's held on by 2 clips and 2 clamps, very easy job. Part number for the pump is 3363394.

Question edited for clarity. You can decode from the serial number. This says 1982.

Whirlpool Date Codes

Electrical-Forensics https://www.electrical-forensics.com > MajorAppliances An alpha code in the model number indicates the year the model was introduced. Before 1981, the second digit of the model number contained the code. After 1981, ... This one is 1993 https://www.fixya.com/support/t1006047-whirlpool_stylemaster_4214164 ..

There appears to be a solution here

Why has my whirlpool washer started asking me about

JustAnswer https://www.justanswer.co.uk > appliance > h42zj-whirl... Jun 24, 2021 - I dont have an error code. I set my washer to wash (press play) it senses then asks 'compartment II 53ml? I have to then press play again ... I have a whirlpool 6th sense zen 12 kg washing machine Jan 7, 2023 Error f24 on my machine, Whirlpool 6 sense I'm not sure how May 1, 2022 How do I remove demo mode from my whirlpool 6th sense 9kg May 13, 2021 My 6th sense Whirlpool dryer has stopped working. 2 red LED Jul 29, 2014 More results from www.justanswer.co.uk A little more here https://www.google.com/search?q=Whirlpool+6th+sense+is+displaying+this+message+Compartment+II+37ml ..

What is the model number for this washer?

Check the Coin Mechanism: Ensure that the coin mechanism is functioning correctly. Sometimes, coins may get stuck or not register properly. Verify that the coin slots are clear and that the mechanism is engaging properly. If there's an issue with the coin mechanism, it could prevent the washer from starting. You might need to clean or repair it. Inspect the Wiring: There should be a harness with two wires that go into the coin mechanism box. Check if these wires are intact and properly connected. If you find any damage or loose connections, consider repairing or replacing the wiring. Bypass the Coin Mechanism: If you suspect that the coin mechanism is causing the problem, you can bypass it temporarily. Cut the wires going into the coin mechanism and insert a push button switch in the line. This will allow you to manually start the washer without relying on the coin mechanism. If you're unsure how to do this, consider contacting a local repair shop for assistance. Check for Other Issues: Inspect other components such as the lid switch, control board, and start button. Any malfunction in these parts could prevent the washer from starting. Make sure the washer is plugged in and that there are no tripped circuit breakers or blown fuses.

Check the suspension springs for stretching and shock absorber for operation. I am having difficulty finding that model. https://www.google.com/search?q=Whirlpool+Cabrio+wtw6707w2+washer%2C+UL+code ..

The F20 error code on a Whirlpool Duet Steam Washer typically indicates a water inlet problem. It means the washer is not getting enough water to continue the wash cycle. This can be due to several reasons, even if it seems like water is flowing fine at first glance. Here are steps you can take to troubleshoot and potentially resolve the issue:

1. Check Water Supply Hoses:
   • Ensure both the hot and cold water faucets are fully open.
   • Inspect the water inlet hoses for kinks, bends, or twists that could restrict water flow. Straighten out any issues you find.
   • Turn off the water supply, disconnect the hoses from the back of the washer, and check that the filter screens inside the water inlet valve are not clogged with debris. Clean them carefully if needed.
2. Water Pressure:
   • The washer requires a certain amount of water pressure to function correctly. Low household water pressure can lead to insufficient water flow to the washer. Make sure your home's water pressure is within the washer's required range.
3. Check for Siphoning:
   • Make sure the drain hose is correctly installed. The end of the hose should not be too far down the standpipe, and there should be an air gap to prevent siphoning.
4. Inlet Valves:
   • If the water hoses and screens are clear, there might be an issue with the water inlet valves themselves. They might not be opening fully due to electrical issues or mechanical failure.
   • The inlet valves can be tested with a multimeter for continuity to ensure they are functioning correctly. If they lack continuity, they need to be replaced.
5. Flow Meter:
   • Some Whirlpool Duet models have a flow meter that measures the amount of water entering the washer. If this component malfunctions, it could mistakenly signal that there's not enough water, even when there is.
   • Diagnosing a flow meter requires some technical knowledge and a service manual for your specific model.
6. Pressure Switch:
   • The washer uses a pressure switch to monitor the water level. If there's an issue with this switch or the hose connected to it, the washer might incorrectly interpret the problem as insufficient water flow.
   • Check the pressure switch and the hose for any blockage, disconnection, or damage.
7. Reset the Washer:
   • Since unplugging the washer hasn't cleared the error, after checking the above, try to reset the control board by unplugging the washer for about 5 minutes, then plugging it back in.

If after trying these steps the F20 error persists, it may be time to consult the manual for more specific troubleshooting steps for your model or contact a professional appliance repair service. Sometimes, the problem could be related to the washer's electronic control board or other components that require professional diagnosis and repair.

Is the correct tension on the belt; too much and the bearing could be getting damaged. If you remove the belt, check the drum moves freely with no noise. If noisy, replace the bearing or purchase a new machine.

Stale smells come from not drying the front gasket trough just inside the door. Your bleach isn't cleaning that area. Use Tilex Mold spray on it. Clean and dry the door glass as well and leave the door open for a few hours after a wash or leave it open all the time. If it is dry, it can't smell.There will always be some water in the pump area, but if you remove the pump filter cover, that releases and water left behind.When you use bleach always do whites or your tea towels next. You can also dilute by adding a couple of jugs of water first.There is a trick to look for rattling items between the inner and outer drum. Put a good flashlight against the holes in the drum and you can see what is below without getting the glare from the drum.These websites give you a full parts schematic showing all the parts and their positions.https://www.appliancepartspros.com/tub-basket-parts-for-whirlpool-wfw94heaw0.htmlWhirlpool Washer WFW94HEAW0 - OEM Parts & Repair Helppartselect.cahttps://www.partselect.caCanada Wide Same-Day Shipping For All In-Stock Parts. Shop Canadian And Avoid Customs ' 2 Million Parts Ready To Ship. OEM Parts & Accessories. One-Year Warranty. Money Back Guarantee. Free Repair Help & Videos. Types: Dishwasher Parts, Dryer Parts.

If the machine runs a while and then drains, it is like that there is a leak and the leak sensor has been activated. There is a tray between the base of the machine and the kitchen floor.

Check if the water is getting hot. F08 indicates that the heater is an open circuit so check the heater for continuity with a meter.

With the machine powered on, press and hold both the Rinse and Spin buttons down at the same time for 3 seconds.

oL is an Overload error. Try running a cycle empty. If oL (overloaded) appears in display, the load too large. If an overload is detected, the washer will drain any water and detergent in the washer. Remove several items and add HE detergent. Close lid and press START/PAUSE.

oL - Error Code - Washer - Product Help ' Whirlpool

https://www.google.com/search?q=whirlpool+cabrio+ol+error ..