20 Most Recent Whirlpool Ultimate Care II GSW9650LW Top Load Washer - Page 7 Questions & Answers

Search online for the manual for your make and model. It ,may be that a sensor is not working properly.

Whirlpool... | Answered on Oct 18, 2019

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.Jun 13, 2019

Error Codes in Front Load Washers - Whirlpool Home Appliances

https://producthelp.whirlpool.com > Washers > Washer_Product_AssistanceSearch for: How do I clear the error code on my Whirlpool washer?

Whirlpool... | Answered on Oct 12, 2019

sounds like the motor or clutch pack is bad if so its a expensive fix

Whirlpool... | Answered on Oct 05, 2019

Unplug washer for 30 minutes. Plug back in se if opens. If not take off top panel off washer. There is a latch to release door.

Whirlpool... | Answered on Oct 03, 2019

faulty cold water solenoid is most likely the problem

Whirlpool... | Answered on Oct 01, 2019

the drain hose may be kinked therefore restricting draining of the water or the pump itself is faulty

Whirlpool... | Answered on Sep 28, 2019

New sensor is required will not run if it cannot lock (safety)

Whirlpool... | Answered on Sep 24, 2019

Generally speaking the lid lock works either electrically by a solenoid or on older models when the tub spins it creates a breeze and a blade blocks the lid.

Whirlpool... | Answered on Sep 24, 2019

1. Turn washer off 2. Set the mode selector dial to normal 3. Turn the dial counterclockwise one click clockwise three clicks counterclockwise one click then clockwise one click 4. Now press the start button

Whirlpool... | Answered on Sep 15, 2019

This is usually broken wiring to the drum motor.
There is a cable tie for the wiring 20 cm from the motor plug. There is the normal spot for broken wiring.
It can also me worn out motor brushes.

It has nothing to do with the door lock.

Whirlpool... | Answered on Sep 10, 2019

The codes F5 and E3 indicate a lid lock issue. If unplugging it for several minutes then plugging it back in does not reset it the top of the washer needs to be removed and the lid lock replaced. https://producthelp.whirlpool.com/Laundry/Washers/Washer_Product_Assistance/VIDEO%3A_F5_E3_Error_Code_for_Top_Load_Washers

Whirlpool... | Answered on Sep 09, 2019

drain motors are plugin replacement. No schematic required unless you are still troubleshooting it. If so, pull the washer out and search around. Sometimes schematics are placed for tech use.

Whirlpool... | Answered on Sep 05, 2019

GFCI trips when the current in the line does not = the current in the neutral. This might happen if some of the current is flowing in the ground lead.
Run the machine till it trips, unplug it and measure resistance from line (narrow spade) to ground (round). It should be an open circuit.
Any resistance there indicates a problem in the machine and the reason the breaker is tripping.

Whirlpool... | Answered on Sep 05, 2019

there are highly paid technicians for that.
there is more to the problem than meets your eye so there is not enough info to help

Whirlpool... | Answered on Sep 05, 2019

Not finding what you are looking for?
Whirlpool Ultimate Care II GSW9650LW Top Load Washer Logo

49 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts


Level 3 Expert

85239 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Brad Brown

Level 3 Expert

18562 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Whirlpool Washing Machines

  • Whirlpool Washing Machines

Most Popular Question

disassemble agitator

  • Washing Machines