20 Most Recent Insignia NS- 27" TV27 TV Questions & Answers


If you wish to get some details; visit the site linked here. Pull up older posts.
http://electronicshelponline.blogspot.com/

Insignia NS- 27"... | Answered on Aug 08, 2017


Refer its user manual for more details about a channel scan.

Insignia NS- 27"... | Answered on Feb 25, 2015


www.insigniaproducts.com/support.html

Insignia NS- 27"... | Answered on Jun 13, 2014


AH HAH!!! I had the same problem and FINALLY after 2 days trying to solve the program I got the solution!! Go to source on your remote and choose the proper source. When you do, don't forget to press enter on your remote as well.

Insignia NS- 27"... | Answered on Feb 22, 2014


the exact same thing JUST happened to us, my daughter unknowingly pushed a button, or a combo of buttons on the remote, we got the blue screen with the lock in the left hand corner, tried ALL of the above (we have the same tv, insigna, only 2 yrs old), I typed the problem in on the net and got the solution, pressing the display button worked!!! Thank U who ever knew this!!!

Insignia NS- 27"... | Answered on Apr 05, 2013


Make a hard reset to this set and try.

Insignia NS- 27"... | Answered on Oct 06, 2012


Unplug the TV from AC mains wall socket, and re-plug it back after 10 minutes or so. This will make TV to a hard reset. It must work properly after this, if no other circuit problem persists. If it do not help you, the main system memory IC need replacement. Contact any experienced service technician.

Insignia NS- 27"... | Answered on Oct 06, 2012


You can't select its input without its remote cotnrol.

Insignia NS- 27"... | Answered on Sep 07, 2012


Refer to the manual (free download here). Generally, a blue screen indicates a very low or non-existent signal. This can happen when the antenna is unable to gather enough of a signal from a particular broadcaster, or if an A/V input is selected, but the A/V device is not on or providing a signal. Since you are not seeing channel information when tuning, I suspect that the television is set to display an A/V input instead of the internal tuner.

With a working remote, locate the TV/AV button on the lower left (manual page 3 - item 8). When this button is pressed, you can choose to display signals on the ANT, VIDEO1, VIDEO2 or COMPONENT jacks. The ANT selection chooses the input on the RF jack such as an antenna or cable TV (with or without converter box). If using a cable box, the TV tuner should be set to Ch3 or Ch4 as determined by your cable box. Otherwise, select the VIDEO1, VIDEO2 or COMPONENT input that has the source signals you wish to watch from a cable box, DVD player, etc. that is connected to the rear input jacks. Page 7 of the manual details the connection and remote operation.

I hope this helps!

Insignia NS- 27"... | Answered on Apr 16, 2012


Hello
When an Insignia TV is locked, it keeps you from watching all of your channels by only displaying a black screen. Insignia TVs are locked from a single button command on the remote control, so it is easy for you to lock the TV by accident. Since Insignia TVs can be locked so easily, it's important to know how to undo this command and unlock the TV yourself. So, unlock your Insignia TV with the push of a button and once again enjoy watching your favorite programs.
· Find the lock button on the Insignia remote control. The lock button is located on the third column from the left on the second row from the top of the remote.

·Stand within operating range of the Insignia TV, then aim the remote at the TV's receiver and press the "Lock" button on the remote control.
· Aim the remote at the TV and press the channel buttons to make sure the TV is unlocked. When the TV is locked, it shows a black screen and does not allow you to view anything else. If the screen remains black, press the "Lock" button again. If this doesn't work, change the batteries in the remote and start over at step
OK

Insignia NS- 27"... | Answered on Sep 17, 2011


Hello,

The issue you describe is consistent with a power supply board issue. This is the board where the AC goes to. This problem may have occurred as a result of irregular power supply, or excess power supply or power surge.

The TV is receiving current but cannot circulate or transfer the current to other necessary part of the TV because of the defective power supply board. You might be lucky it's just a blow fuse. Also a defective transformer can cause your TV not to power on.

All these can be checked on the power supply board.

But more often bad capacitors causes problem on the power supply board. I do not think the power board needs replacement, rather those defective capacitors is causing this issue. Open unit up and take a look at the power supply board.You will probably see one or more electrolytic filter capacitors that are bulged up in the top-not perfectly flat like the others.

The value of these capacitors will be different, most likely they will be somewhere around-820 to 2200uF/25 V( or /10V sometimes)

You can replace them with same values but I would recommend the voltage rating to be higher(like 35V for an original 25V) for reliability purposes.

What happens is,these bulged top capacitors will cause a low and unfiltered DC voltage=main board will malfunction(the relay will keep clicking until the caps are holding enough charge to bring the voltage up over a threshold point).

You can buy these capacitors at any Fry's or Radioshack store or you can order them online at vendors like "mcmelectronics.com"(look for electrolytic capacitors). After replacing these capacitor(capacitors) most likely the normal operation will be restored. Or you can by a refurbished complete power board to save you some stress.

Note: There may be also some other causes for this symptom ,like a defective T con board ,or main board,but the bulged top capacitors are the most common cause for this issue.

If you don't know about TV repairers, take the TV to the nearest repairman to fix the fault for you. Also, note that TV stores a lot of current, so wait a while before opening the TV back cover.

I hope this helps.

Regards.

Insignia NS- 27"... | Answered on Sep 07, 2011


Hello
Your Insigina TV has no built in digital tuner. It has VHF/UHF/CABLE IN tuner. It is not a digital one. OK.

Insignia NS- 27"... | Answered on Jun 13, 2011


You have a problem with your high voltage section(flyback transformer).That crack you hear is your high voltage(12k+)arching to grd.This trans. supplies voltage to diff. sections of the tv.That is why your audio is affected.That particular section has to be inspected by a competent repair person.

Insignia NS- 27"... | Answered on Feb 28, 2011


try 0000 (or) 1234

Insignia NS- 27"... | Answered on Feb 27, 2011

Not finding what you are looking for?
Insignia NS- 27" TV27 TV Logo

86 questions posted

Ask a Question

Usually answered in minutes!

Top Insignia Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76237 Answers

Cindy Wells

Level 3 Expert

6073 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1691 Answers

Are you an Insignia Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Insignia Televison & Video

  • Insignia Televison & Video

Most Popular Question

37 inch widescreen insignia son

  • Televison & Video
Loading...