Top 20
Whirlpool LTE6234D Top Load Stacked Washer/Dryer Questions & Answers
Whirlpool Thin Twin WET3300SQ (water stops coming in)
- We are sorry to hear of the problem with your Whirlpool washer. We would recommend having a local certified technician in your area properly diagnose and repair the issue you are experiencing. Please email us at [email protected] with your name, phone number, address and the model and serial number for your washer.
4/7/2017 8:36:03 PM •
Whirlpool...
•
292 views • 0 helpful votes
How to take off front of dryer to replace dryer switch
the face of dryer does not come off but you can remove the bottom face of the dryer by using a putty knife then slide it between the two pcs and pull at the same time this will allow it to pull away at the top of bottom panel then lift slightly as the two bottom clips just slide into place. this will allow you access to the thermo sensors if that is what you are referring to. when you say dryer switch
5/21/2016 2:52:44 AM •
Whirlpool...
•
83 views • 0 helpful votes
Water level TOO HIGH
Most likely the water level switch. If you have water running into tub after it is shut off could be the inlet water valve is not shutting the water completely off. Hope this helps
6/18/2014 7:42:45 PM •
Whirlpool...
•
96 views • 0 helpful votes
Whirlpool thin twin #LT7000XUNO washer timer doesn't turn, have to do everything manually. Easy fix?
A) I've never worker on the dual stacked setups.
B) Standard topload is easy. Make sure you unplug it first, locating a replacement timer will be the hardest part. Most places around here are "wholesale" and only sell to techs. You used to could walk in with a maintenance uniform and buy the parts, for cash, then they started requiring company accounts. We still have at least one that sells retail parts. You may have to check the internet. You'll need the Manufacturer, Model, and , maybe the serial number.
Then the access to the backside of the timer usually involves removing a back panel or lifting the entire top of the assembly. With a dual I'd figure it to be a back panel.
C) Then you second hardest and most critical part is labeling your connections and making sure that you plug them into the exact same place on the new one that they now reside on the old one.
4/19/2014 10:06:50 AM •
Whirlpool...
•
479 views • 0 helpful votes
Dont know how to remove cabinet on frigidaire
to remove the front panel on the washer you have to remove the 2 screws at the bottom of the panel then the panel will drop down out of the slip and groove hooks and you can remove panel
10/29/2013 12:35:08 AM •
Whirlpool...
•
133 views • 0 helpful votes
Dryer drum makes noise
You did not describe how the noise was. Normally, the noise comes from the drum rollers was clogged or frozen. The other source of noise comes from the belt bearing was bad. Taken off this dryer is hard-may need 2 people to get the job done.
10/22/2013 3:36:45 AM •
Whirlpool...
•
69 views • 1 helpful votes
My washer won't drain the dirty water and will
The pump that removes water could be blocked by debris. Oftentimes rugs and even towels can shed a significant amount of lint or loose fibers that cannot pass through the pump. I have also seen socks, underwear, change, buttons, and other things I wont mention clogging a pump. Depending on the make of your machine the pump is either driven by the main motor or by its own smaller electric motor. It must be accessed by removing the washer case. the pump is usually secured by screws or clamps and connected to drain hoses by hose clamps. There is also the possibility that the pump has experienced a mechanical failure and needs to be replaced.
9/16/2013 2:45:52 PM •
Whirlpool...
•
143 views • 2 helpful votes
Thin twin tub loose
you will need to remove the front panel of the washer,there are 3 spring suspension rods below the tub and either one or more of these springs are disconnected from the tub or broken
12/7/2012 12:45:02 AM •
Whirlpool...
•
2,159 views • 2 helpful votes
Not finding what you are looking for?