20 Most Recent Whirlpool LTE6234D Top Load Stacked Washer/Dryer Questions & Answers


sounds like a failure of the control unit, best to have it checked out by repairer

Whirlpool... | Answered on Feb 03, 2018


It is replaceable it just pull off.

Whirlpool... | Answered on Nov 28, 2017


I can not find your model number that you posted.
I can tell you that all whirpool thin twins up to last year were direct drive with no belt except for the dryer section. Whirlpool stackers from the early eighties did have a washer belt if yours is this old replace the entire machine.

Whirlpool... | Answered on Jun 22, 2017


  • We are sorry to hear of the problem with your Whirlpool washer. We would recommend having a local certified technician in your area properly diagnose and repair the issue you are experiencing. Please email us at [email protected] with your name, phone number, address and the model and serial number for your washer.

Whirlpool... | Answered on Apr 18, 2017


Hi, Do you know if the washer spins at all?
It sounds like the coupler has gone bad.
Please let me know if it spins at all.
I can send yyou instructions on changing the coupler.

Vic

Whirlpool... | Answered on Nov 03, 2016


the face of dryer does not come off but you can remove the bottom face of the dryer by using a putty knife then slide it between the two pcs and pull at the same time this will allow it to pull away at the top of bottom panel then lift slightly as the two bottom clips just slide into place. this will allow you access to the thermo sensors if that is what you are referring to. when you say dryer switch

Whirlpool... | Answered on Jun 04, 2016


You didn't give to much detail about the noise, other then clunking. Does it sound like it's metal against metal? Does it sound hollow? When does the noise take place before, during or after the spin cycle.

The easiest thing to do is check to see if the motor is loose, or if you might have too much slop or slake in the belt, if you do then replace and readjust the belt.

Whirlpool... | Answered on Jan 07, 2016


Most likely the water level switch. If you have water running into tub after it is shut off could be the inlet water valve is not shutting the water completely off. Hope this helps

Whirlpool... | Answered on Aug 09, 2014


What are you calling the below washer don't know what you are talking about. thanks

Whirlpool... | Answered on Aug 09, 2014


Are you sure that's not thermostat not thermostart . There are lots of different ones you would need to know which one a part number on it.

Whirlpool... | Answered on Jul 12, 2014


you need to drain the washing machine by removing the little door below the drum door and pll out the the hose with a white knob (beware alot of water comes out so have a couple of pans ready. the fault means that there may be a blockage in the debris filter (next to the outlet hose yuo just pulled out) am sure you have prob already discovered the fix by now though!

Whirlpool... | Answered on May 25, 2014

Not finding what you are looking for?
Whirlpool LTE6234D Top Load Stacked Washer/Dryer Logo

340 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Brad Brown

Level 3 Expert

18438 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Whirlpool Washing Machines

  • Whirlpool Washing Machines

Most Popular Question

washer drain dirty water will

  • Washing Machines
Loading...