Whirlpool GMC305PD Electric Single Oven - Answered Questions & Fixed issues
How to set time with new control board?
You may set the clock on your Microwave per page 6 of the User Guide by following the steps below. We've included the link for the User Guide below.
https://www.whirlpool.com/content/dam/global/documents/200105/owners-manual-8300610.pdf
This is a 12 hour clock and does not show a.m. or p.m. To Set: Before setting, make sure the oven, Timer and Timed Cooking are off. 1. Press CLOCK. 2. Press the HR or MIN "up" or "down" arrow pads to set the time of day. 3. Press CLOCK or START/ENTER. To Disable: The clock time can be disabled so that it does not show on the display. To disable, press and hold CLOCK for 5 seconds. To display the clock time again, press and hold CLOCK for 5 seconds and the time of day will show on the display. The clock time should not have to be reset.
11/3/2017 7:31:06 PM •
Whirlpool...
•
Answered
on Nov 03, 2017
•
597 views
Door latch stuck
This error means your temperature sensor (probe) has failed and needs to be replaced.
11/5/2014 8:19:23 PM •
Whirlpool...
•
Answered
on Nov 05, 2014
•
485 views
E-1 & F-5 come on after about a minute when
The E1- F5 error is a door lock error.
The control (TIMER) has likely failed in this instance - BUT...
Sometimes when you disconnect power to a range and reconnect it the electronic range control gets confused.
You should disconnect power again for 15 seconds and reconnect and see if that helps.
If it doesn't cure the E1- F5 error hold the bake button in until E0- F2 appears in the display.
This is the error for a stuck button on the keypad and is the way to clear the memory of the electronic range control.
Sometimes these work, but if the control has failed it won't make any difference.
Thanks for using FixYa
10/21/2011 12:13:41 AM •
Whirlpool...
•
Answered
on Oct 21, 2011
•
126 views
The display is not working
Hi!!
Unplug unit from wall outlet for 10 min. to reset the microcomputer. If this do not work, make sure the unit hasn't been set to Sabbath Mode by accident, when this happens there is no display on the board. Check your user manual to enter/exit the Sabbath Mode. If this is not your case, disconnect the unit form the wall outlet, check the flat connector from the membrane Switch (on the control panel assembly) to the microcomputer (PCB).
In case the unit works but the the only problem is the display, replace membrane switch. Here is a diagram of the Control Panel Assembly and components.
Illust. Part No. No. DESCRIPTION
2. 4450356 Gasket
3. 8302320 Microcomputer
4. 8281179 Screw
5. 8301848 Board, Mtrzd Latch
6. 4451592 Filter
7. 4451632 Filter Bracket,
8. 4449809Screw, 8?18 x 3/89
9. Control Panel Assembly with Membrane Switch
- 8300409 Black & Black Stainless Models
- 8300408 White Model
- 8300406 Biscuit
10. 4449745 Screw
Good Luck! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.
11/21/2010 2:38:45 AM •
Whirlpool...
•
Answered
on Nov 21, 2010
•
156 views
Oven door is locked after trying to clean and
E1 F5 means your unit is having a problem with the door latch and lock assemble turn the power off for 10 min. and after turning the power back on wait another 10 min. before opening
4/6/2010 12:17:53 AM •
Whirlpool...
•
Answered
on Apr 06, 2010
•
494 views
GMC305PD
appears that it is starting up the self cleaning feature ( which runs the temp up to the max to burn off any grease etc ) and locks the door.. You may have a defective control board.. or check the self cleaning switch position to make sure that is not activated... Hope that helps..
8/19/2008 1:12:16 AM •
Whirlpool...
•
Answered
on Aug 19, 2008
•
206 views
Whirlpool YWFE710H0BS0 oven no longer heats up.
Check the elements for continuity with a multimeter. Sometimes the connectors draw too much current and can burn out as well. Both are easy tests. A runaway temperature can make elements fail because there is no thermostatic control, they just glow bright yellow..
8/26/2023 10:38:37 AM •
Whirlpool Ovens
•
Answered
on Aug 26, 2023
•
56 views
What does E1 F2 code means?
Greetings,
This might indicate a bad keypad or that the cable connecting the keypad to the chip board within your whirlpool has come loose. You might need to work with whirlpool to see if they keypad needs replacing or if the internal chip board itself is faulty.
Thank you.
4/24/2023 6:16:24 PM •
Whirlpool Ovens
•
Answered
on Apr 24, 2023
•
83 views
How to set the clock to not display time
the time?
You can turn off the clock display from the oven's control panel. Look for a setting that says "Clock" or "Time of Day" and set it to OFF. If you don't have this option on your oven, contact the manufacturer directly and they will be able to help you.
2/23/2023 12:33:19 PM •
Whirlpool Ovens
•
Answered
on Feb 23, 2023
•
526 views
Not finding what you are looking for?