Whirlpool RBD305PD Electric Double Oven - Page 7 - Answered Questions & Fixed issues


it may have back lite lcd display and the lights have blown shine a torch into the lcd if you can read it then you need the backing lights replaced

Whirlpool... | Answered on Apr 21, 2010 | 473 views


Hi,
What is your exact model #? This sounds like it could be other things besides the control panel or it could be the control panel... It could be as simple as a loose wire somewhere. If your model is RBD305PD?? control panels are available however parts alone could be in excess of $200-300. I may or may not be worth replacing at that price... I would guess most techs would charge $300-600 or more in some places... depending on the exact model and how difficult it is to access.

Whirlpool... | Answered on Apr 15, 2010 | 123 views


Yes it is a fairly straightforward repair
If it is built in, then you will have to remove it from the unit.
The fan is usually located at the top of the outer casing, sometimes at the front, and others at the rear.
If it is freestanding, then it will mean removing side panels and top to gain access to the fan.

Whirlpool... | Answered on Apr 08, 2010 | 178 views


could well be the grill element blown.

Whirlpool... | Answered on Mar 20, 2010 | 420 views


Cavity limit failure most likely page 38

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Whirlpool... | Answered on Mar 13, 2010 | 133 views


There will be some noise from the fan, but it should not be excessive, if it is really loud, then this is an indication that the fan is failing, and should be replaced ASAP.

Whirlpool... | Answered on Mar 12, 2010 | 1,508 views


the display board itself would be the culprit,the part might be under warranty,if under 5 years consult manual or manufacturer for coverage....the part is probably expensive

Whirlpool... | Answered on Mar 06, 2010 | 1,396 views


I posted a blog on this subject at this link:

appliancejunk.com/blog/2009/11/11/whirlpool-oven-e6-f2-error-code-failure-andor-blank-display-board-not-available/

perhaps this will help you.

Best Regards,
Bruce
www.fixyourboard.com

Whirlpool... | Answered on May 27, 2015 | 407 views


We repair a lot of control boards for this particular failure. Here's a link to a short article addressing this problem:

www.fixyourboard.com/techzone/ovens/e6_f2/e6_f2.html

Hope this helps you out!
Best Regards,
Bruce
www.fixyourboard.com

Whirlpool... | Answered on Mar 03, 2010 | 527 views


Look for a blown fuse mounted on back of the controleb59c28.pngtis page is in the MANUAL

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Whirlpool... | Answered on Feb 10, 2010 | 976 views


296802f.pngManual
The above manual will give an idea what to look for and where


If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Whirlpool... | Answered on Feb 07, 2010 | 1,458 views


The clock control ,(eoc), is going bad. eventually the oven will quit too. Sorry, hope this hels.

Whirlpool... | Answered on Feb 02, 2010 | 202 views


Most fan ovens have a control sensor which allows tthe fan to operate even after you have turned the oven off to prevent overheating.

It sounds as if this sensor has stuck in the closed position thus leaving the fan running .

You will need to replace the fan control unit at the back of the oven.

Whirlpool... | Answered on Dec 31, 2009 | 871 views


There is a non-resettable fuse on the back of the oven that will have to be replaced. The oven will have to be removed from the wall and the back panel removed from the oven to access the fuse.

Whirlpool... | Answered on Nov 22, 2009 | 499 views


Hi.
You need to replace both the door hinges, as the hinge springs have become weak.
Please rate my solution.
Thanks.

Whirlpool... | Answered on Nov 22, 2009 | 341 views


If the fan is working o/k, then you need to fit a new oven element, located at rear of oven behind removeable cover.
Please rate my solution.
Thanks.

Whirlpool... | Answered on Nov 18, 2009 | 352 views


Your oven temperature sensor has failed(e-2) as well as your electronic control board(f-6). The oven temp sensor, electronic control board and the touchpad must be replaced . Approximate cost of parts is $500.00. Before you decide what to do, check the thermal fuse at the control panel first. If blown, replace it and the temp sensor. If you are lucky the control board may still be good.

Whirlpool... | Answered on Nov 11, 2009 | 1,535 views


When this code appears and display is going blank too, it is always the control board. The only option is to buy a new one or get it repaired. It can be fixed quickly and reliably. www.fixyourboard.com

Whirlpool... | Answered on Nov 09, 2009 | 1,480 views


You have to clean the bottom part with "Easy Off" Oven cleaner. You can buy this at the grocery store and there are now easy instructions on the can of a cold or hot oven directions.

It is easy and you CAN do this so please let us know when you get this cleaned out. And happy holidays to you, too! :>)

Whirlpool... | Answered on Nov 08, 2009 | 200 views

Not finding what you are looking for?
Whirlpool RBD305PD Electric Double Oven Logo

409 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Ovens Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Cindy Wells

Level 3 Expert

6181 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Are you a Whirlpool Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...