Whirlpool RBD305PD Electric Double Oven - Page 2 - Answered Questions & Fixed issues

not sure what you mean but do you have the anti tip bracket installed? it keeps stove from tipping forward when door is opened connects to wall and stove leg or adjuster

there should be a 40 amp breaker in your electrical panel turn off and back on again to reset power

Okay this doesn't make sense did the breaker trip if so look for a short to ground I have serviced many of wall ovens in self clean the TOD does trip do you have a display if not the thermal cavity fuse is open if it stopped in self clean the door is locked as a tech I went to the auto store and bought some feeler gauges use one at the top of the door in the middle slide gauge between door and body push to the left to release the catch door should open

Hello there. From the manual I got To Stop Self-Clean any time: Press UPPER OFF, LOWER OFF or OFF/CANCEL. If the oven temperature is too high, the door will remain locked. It will not unlock until the oven cools Hope it helps/

You need to remove the inner door panel, Usually a few screws holding it on. On some models the handle screws also need to be removed. Do it slowly and carefully as the door may want to swing up quickly, once the weight on it is removed. Pay close attention to each step so all screws etc go back in the same place. Make a diagram as you take them out to be sure.

First thing is to reset the breaker, it's tripped right now, so turn it on then off again then back on. If it kicks right back off again leave it off as you have a dead short and that can be dangerous especially with an electric oven. In that case call an appliance repair person. If the breaker stays on after you reset it go back to your oven and see if it has come back on and is working. If it has power but the display is flashing some error code you will need to troubleshoot with the owners manual or look online for a manual. If the oven is only a few years old it should "reboot" itself when power is restored. Some models require that you manually reset them with some combination of buttons (that's where you need the manual). I hope this helps.

remove the door and reassemble

this is how to replace door hinges

all of them. arnt these visual blow fuses? does the lil wire look broken? or r they all solid state?

It may be the self clean latch not closing or locking

Pull unit slightly out of wall remove display panel screws tilt panel enough to see wires going to control board let know if there is an inline fuse leading to the board reason I ask the schematic does not show this fuse going on memory if so take the best picture you can a submit I'll give you the part # they use 5 different fuses, there is a reason fuse blew did you recently do a self clean does the cooling fan operates this draws air across the electrical components

If is 6 months old call for warranty repair, turn off circuit breaker for a minute then repower this may clear it if not again call for warranty service

Start here

Control Panel has likely failed (circuit board). You can try removing the power wire from the back of the panel and then replug it back in to see if it resets the board, but Im sorry to say your likely going to have to remove and replace the control panel.

door switch/spring is defective or clogged with grease.

Pretty sure it's meant to.

These ovens require that you remove the whole side covering to get to the hinges and door hardware.

My oven lights work. The top oven stopped working and bottom oven was working and it stopped working now. And the control panel is blank and just beeps when the bottons are pressed. What should I check first?

Here is the fuse to order and it is located behind the control panel.

There is a thermal fuse at the connection for the control board.

Had the same problem. I repaired the board myself and ordered a replacement from sears parts direct. It is a repaired board not a new one but has the same warranty. You can get this board a lot faster. Here is the link. http://www.searspartsdirect.com/partsdirect/part-number/8302319R/0022/664. If you would like to repair your own board leave a post and I will help you.