20 Most Recent Whirlpool RF315 Dual Fuel (Electric and Gas) Kitchen Range Questions & Answers


I was baking and the stove suddenly changed to Maxi Broil and then to ERR F2EO Stuck Key. I cannot seem to change it by start or off or even turning the unit off and then back on. Any suggestions? Thanks.

Whirlpool RF315... | Answered on Jan 27, 2013


You need to replace the oven temperature sensor. Here is the part you need to order. To replace the sensor, remove the screw holding it in place, slide it out and unplug it.

Whirlpool RF315... | Answered on Nov 11, 2012


It sounds like you need to replace your heat sensor located inside the rear left top of oven.Also you will need to pull range out and remove back panel to unplug senso good luck:)

Whirlpool RF315... | Answered on May 07, 2009


need strong fingers and a helper... lay the door on the floor push open the hinges and there is a hole on the side of the hinge have your helper slide in a small nail only about 1/4 " in to the hole this will keep the hinge out do the same on the other side then reinstall the door open up and remove your nails

Whirlpool RF315... | Answered on Feb 28, 2008


I notice is it also in French, so I am guessing you are Canadian? Greetings from Mississauga! Its a guess... but..

YGY397LXUS Whirlpool Range Canada - Sale! Best Price ...

www.canadianappliance.ca > Ranges > Whirlpool
Whirlpool Gold YGY397LXUS Slide In Electric Range, 30in, 4.5 cu.ft, with AccuBake Temperature Management System, Self-Cleaning Oven, Delay Bake, ... This AccuBake system uses a sensor to monitor the oven temperature; it will then turn ...

Whirlpool GBD307PDS09 Built In Oven - Electric Timer - Stove ...

www.appliancetimers.ca > appliance
I have a Whirlpool Gold double oven and someone came to house and told me it ... black panel on whirlpool accubake system self cleaning oven gives double ...

Somewhere hidden in the stove, should be the engineers spec sheet. It should be one of these images

https://www.google.ca/search?q=%22whirlpool+gold%22+%22self+cleaning+oven%22+%22Accubake+system%22

Here is your error code

There may be a problem with the Oven Temperature Sensor, the Warming Drawer Sensor (if so equipped), or the associated wiring. Power unit down by turning off the circuit breaker(s) for one (1) minute. ... Monitor the oven for one (1) minute to ensure the error code does not display again.
Dec 14, 2019
F3 E2 - Electric Range - Product Help ' Whirlpool
https://producthelp.whirlpool.com/Cooking/Wall_Ovens_and_Ranges/Electric_Ranges/Error_Codes/Error_Code%2C_Fault_Code_or_Message_-_Oven_Control/Starts_with_F3/F3_E2_-_Electric_Range#:~:text=There%20may%20be%20a%20problem,for%20one%20(1)%20minute.&text=Monitor%20the%20oven%20for%20one,code%20does%20not%20display%20again.

..

Whirlpool... | Answered on Jan 15, 2021


yes, the keytail (connector ribbon) that plugs into the control board is not making good contact. simply cut a slip of heavy paper such as a business card to the width of the ribbon and slide it into the slot along with the ribbon connector. that will help press the contacts on the other side together snuggly and the problem will vanish. if the error ever returns, try pulling out the connector, cleaning the contacts with a pencil eraser, reinserting it into the slot and repeat above with the paper. good luck.

Whirlpool... | Answered on Dec 12, 2020


Try owner's manual, troubleshooting and the F5E0 error code. It may help, otherwise google the error code, or no owners manual? try https://www.manualslib.com

Whirlpool... | Answered on Jun 29, 2020


sabbath == When in Sabbath Mode, your oven will disable its automatic shut-off function to stay on longer than 12 hours. This means that the oven will stay in a Bake mode until shut off, which will allow you to use the oven for cooking or warming food.

Whirlpool... | Answered on Apr 12, 2020


The F2 E0 error indicates a short at the key pad or a wiring issue between the control board and the keypad. Try pressing Cancel. Next turn off the range at the circuit breaker or unplug the range. Wait at least a minute before returning power to the system. Check if the error returns within a few minutes. Disconnect the power again and check the wiring between the control board and the key pad (if these aren't a single assembly). If the wiring connection is loose, secure the wires. If there is corrosion at the contacts, use a contact cleaner on the unit. Let the contact cleaner dry before connecting the power again. If the wires are damaged, replace the broken wires.

If those steps don't resolve the issue, replace the key pad or keypad and control board depending on the unit. If the error returns after replacing only the keypad, then the control board has to be replaced.

Please check the model number of the range. Current Whirlpool range models start with 3 or 4 letters, 2-3 numbers, another letter and another letter and 2 more letters. W10400397B could be a replacement part number for some specific item inside the range or the serial number. It isn't a valid Whirlpool part or model number at https://www.whirlpoolparts.com/ or https://www.partselect.com/Whirlpool-Oven-Parts.htm .

I hope this helps.

Cindy Wells

Whirlpool... | Answered on Oct 24, 2019


Most likely electronic spark ignition for the top burners. So it’s one of 3 parts, the burner switches, the spark module or the igniters on the burners

Whirlpool... | Answered on Oct 03, 2019


William muller, We would like to inquire further about your post with you. Please respond back to this email address [email protected] with your name, user id (William muller), phone number, street address, zip code, reviewer name, model & serial number, and date of purchase on the appliance.

Whirlpool... | Answered on Aug 26, 2019


If it works leave it alone. current is a function of voltage and resistance
The igniter current I in amps (A) is equal to the resistor's voltage V in volts (V) divided by the resistance R in ohms (?):

Whirlpool... | Answered on Jul 29, 2019


The F2 E0 error indicates a communication error at the key pad. The key pad could be faulty. There may be a problem with the wiring between the key pad and the control board. The last possible issue is a problem with the oven's electronic control board. First unplug the range (or turn it off at the circuit breaker) and take a look at the wiring. Disconnect and reconnect the wiring harness between the key pad and the control board. Check for any damaged wires in the wiring harness or corrosion where the wiring harness connects (and in the plugs) on both sides. If the wiring is okay, connect the range to power and wait to see if the message recurs. If it does, you'll need to replace the key pad. If the error recurs, then replace the control board when that is sold as a separate assembly.

There is a parts diagram and pricing list for the RF265LXTB1 here: https://www.appliancepartspros.com/parts-for-whirlpool-rf265lxtb1.html . On this range, the replacement key pad and the control board are sold as a single unit. It's part 11 on the Control Panel diagram.

I hope this helps.

Cindy Wells

Whirlpool... | Answered on Jun 25, 2019

Not finding what you are looking for?
Whirlpool RF315 Dual Fuel (Electric and Gas) Kitchen Range Logo

8 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Kitchen Ranges Experts

Cindy Wells

Level 3 Expert

6220 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Whirlpool Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Whirlpool Kitchen Ranges

  • Whirlpool Kitchen Ranges

Most Popular Question

f2 error whirlpool dual fuel range

  • Kitchen Ranges
Loading...