Whirlpool RCS3014 Electric Cooktop - Answered Questions & Fixed issues


I'm giving you the installation guide in case you need it:
http://www.whirlpool.com/digitalassets/RCS3014RS/Installation%20Instruction_EN.pdf
Ther isn't a whole lot that can go wrong with these, you probably have a bad switch. Hopefully you have a false drawer or accsess to the bottom of it pull the knob off the switch in question, it nay have screws holding it in place from the top, if not, you'll have to get to the underside anyway, switch out the switch in question with one you know works. I beleive this will find your culprit.

Whirlpool... | Answered on Jun 18, 2011 | 85 views


the electric elements should unplug from their electric connectors. remove the knobs. see if the control panel lifts off, or screws off. after removing all of these things maybe you can tell how to get to the screws or how to remove the top of your cooktop.

Whirlpool... | Answered on Jun 22, 2010 | 144 views


Is this a ceramic hob? If it is, you will need a ceramic hob cleaner (john lewis does one) OR Astonish oven/pan cleaner, a non-scratch washing-up sponge and a fair amount of elbow grease. This works for me.

Whirlpool... | Answered on Oct 06, 2009 | 305 views


There should be a diagram in the installation instructions packed with the unit showing how to connect them.

Whirlpool... | Answered on Sep 02, 2009 | 354 views


We Use Debruce Polish on all our cooktops. Debruce also works on stainless steel and polished granite, marble, porcelain, formica and glass. DeBruce is non-toxic odor-less and eco-friendly. You can get DeBruce on line at debrucepolish.com.

Whirlpool... | Answered on Aug 24, 2009 | 349 views


sounds like you got a short(probably one of your switches. do alll the knobe feel as if they're turn the same.usally when one shorts out itll operate differntly no resistance in the switch, can you lift stove top up and look under generally a visual inspecton will show where "pop" occurred

Whirlpool... | Answered on Feb 25, 2008 | 361 views


Can you get to the switch terminals and try jumping them out with a piece of insulated wire? That would tell you if the switch is defective (my suspicion). Please be careful not to touch any live terminals - only the wire insulation you use for the jumper.

Whirlpool... | Answered on Aug 03, 2017 | 393 views


unplug it and replace the main board or get a new stove

Whirlpool... | Answered on May 08, 2015 | 126 views


What is the model number?

Whirlpool... | Answered on Jun 17, 2014 | 116 views


You didn't mention if it only pops when you first turn them on or that the popping is continuous.

If it when you first turn them on, then I would suspect late ignition. Too much gas build-up before ignition takes place. The spark gap may need to be adjusted or the spark module replaced.

If it happens continuously there may be a short in one of the switches or wiring harness.

Whirlpool... | Answered on Jun 01, 2014 | 102 views


and the problem is? please post afresh with full details

Whirlpool... | Answered on May 13, 2014 | 93 views


Sometimes after a power failure the p c board needs re setting. Turn off the power for a few minutes that allows it time to re set. Turn it back on then individually turn on each element for a couple of minutes.

Whirlpool... | Answered on May 10, 2014 | 127 views


Hi,

Recheck the wiring to that switch you replaced, the light circuit was wired wrong, some switch have moved terminals on them so recheck them all.

Good Luck

I’m happy to help further over the phone at https://www.6ya.com/expert/gere_bf68e6055dd61249

Whirlpool... | Answered on Apr 02, 2014 | 112 views


Lift the top of your stove, then look for a connector or plug, wire that has pushed up near or against the stove top. Where the wires connect to the burners one or more may be loose an needs tightening.

Whirlpool... | Answered on Mar 26, 2014 | 181 views


power off to the stove at the electrical switchboard.
wait a minute then power on again, set clock again, any better?
if not, call the repair man.

Whirlpool... | Answered on Oct 23, 2013 | 122 views


We discovered if you press in both the oven control knob and the temperature control knob simultaneously for several seconds, the stop message goes away and the oven returns to normal.

Whirlpool... | Answered on Mar 20, 2013 | 528 views


should be able to clear out and reset clock. If I remember right it means Power Failure, which just means you lost electricity

Whirlpool... | Answered on Oct 15, 2011 | 185 views


Hi joyce_hudak,

Moisture or water have come into contact with your ignition devices, they just need to be dried.

Please follow my directions on the Tip below on how to do this:

GAS STOVE CLICKING PROBLEM...


Kind Regards

JEDEMEYER1

* If this solution helped you, please rate it

Whirlpool... | Answered on Sep 08, 2011 | 105 views

Not finding what you are looking for?
Whirlpool RCS3014 Electric Cooktop Logo

Popular Tags

9 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Cooktops Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Gustavo Ortiz
Gustavo Ortiz

Level 3 Expert

637 Answers

Cindy Wells

Level 3 Expert

6224 Answers

Are you a Whirlpool Cooktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...