Uniden TRU9480 Cordless Phone - Answered Questions & Fixed issues

Are you trying to get the messages from the phone directly or by calling into your phone.

If the answering system is on, then you can play back the messages from the base by pressing the Play/Stop button.To delete a message from the base, press the Delete button (has a 0 with a slash through it) while the message is playing. To delete all messages, press the Delete button when the phone is in standby. From the handset press the Messages softkey (has an envelope icon) when the phone is in standby. Then press Play/2 to play back the messages. To delete a message, press Delete/4 while it is playing. (Deleting all messages can only be done at the base.)

If you are calling into your phone system, you need to have set a two-digit PIN from either the base or the handset and remember it. Then call the number for your phone from a touch tone phone, press 0 and then the PIN within 2 seconds. (Do this while your greeting is playing or after a series of beeps when the phone answers your call after 10 rings if the answering system was off.) If the system is off, start by pressing 0 6 to turn it on. Press 0 2 to play back the messages. (All commands need to be entered within 15 seconds of the last command finishing with both keys pressed within 2 seconds.) To delete a message, press 0 4.

Uniden has the manuals for most of their phones on their support site: http://www.uniden.com/scat/cordlessphones_mnl . Phones are listed in numerical and alphabetical order; thus the TRU9480 manual is on page 7. The direct link to the TRU9480 is http://www.uniden.com/content/ebiz/uniden/resources/ownersmanuals/TRU9480om.pdf .

I hope this helps.

Cindy Wells

Here are two supported AC Adapters for DSS7855 series,
1. Ebay
2. Batteryshack
Both are from the same seller at different online stores.
Hope this helps.
Let me know if you need further help.
Good Luck.
Thanks for using FixYa.

check for poweer on the base or the adapter

They do not sell replacement parts for these, you will need to replace the whole unit. Sorry :(

Hi,when a phone does not come on, it is either the battery of the phone is dead,
might need to be charge or replaced with another battery.

you can use another battery to test if it is the battery the fault.

The other thing to check is if the phone memory is weak and may need to be restored
back the phone memory.
will need to be flashed.

Take care.

I found this elsewhere:
I've fixed this by taking the phone apart, finding where the pressure pads are under the button. I glued a small piece of aluminum foil on to where the pressure pad is. Aluminum foil is a good electrical conductor. It's a delicate process. I don't recommend doing this unless you know what you're doing. But if your handset is already dead/useless, give it a try. Put everything back together and the buttons work again.

The handset displaying the message may have lost its memory of the base station. Take it over to the base station and reset it as when you first associated the handset with the base.

I hope this helps.

Cindy Wells

It is likely your phone has a mouthpiece or ear piece problem that is why the reciver can't hear you.So your need to take the phone to the nearest repair office for it to be changed.

see if it is turned off at the provider. ring and ask for the codes to turn them on and off.

if you suspect the problem is with your device, then reset the phone by following the instructions given in the instruction book which came along with your phone..if it still doesnt work then check the connectivity by connecting some other phone(friend's phone) with your landline cable.if the new phone is also not able to receive calls then contact ur service provider..but if the friend's phone works with your land line connection then pls report again

Press or hold the DND button. The light will go out.

The phone can not do that. You will need to call the company that supplies your dial tone to ask them for the code to forward out.

It is also possible that you do not have that feature.

Here is the manual.

As far as the transferring calls on a secondary line, use the flash button.

The answering machine is full, delete the messages.

The answering machine is full, delete messages

It means the answering machine is full.

I too purchased an Uniden phone for India. Everything except the caller ID works fine. The caller ID wont work as the technology used in India is different. Try purchasing a FSK to DTMF converter or a separate caller ID box.

Hi streck - Below is the link for your manual. The manual is the same for all 9480 series phones no matter how many extra handsets you have. If this solves your problem PLEASE rate this as fixed. If you need more help just add a comment and I'll be happy to assist you further. Thanks.

http://www.uniden.com/pdf/TRU9480om.pdf

Jeff

the wire goes down the middle of the pack and not the sides. tpo or bottom it doesnt matter I’m happy to assist further over the phone at https://www.6ya.com/expert/james_1cb31da1bc8c6102

are you running a wireless router? try unpluging router to test phone. I’m happy to assist further over the phone at https://www.6ya.com/expert/james_1cb31da1bc8c6102