Top 20 Chevrolet 1995 Chevrolet Blazer S10/jimmy S15 Radio Questions & Answers

my wiring shows no relay,wiring goes direct from stereo to speakers, have you tried to adjust the fade control on the stereo?

Neutral, however you can move the tang to fit the slot when installing. Just make sure the new one matches your old one when you remove it, and make sure your new one matches, you will be fine.

If possible try switching the wires on the neutral safety switch or pull off the plug and turn it over, so the contacts are on the opposite terminals.. If that doesn't work, it's possible you got a bad switch right out of the box. It DOES happen.

what switch are you intalling

check sparkplugs,air filter fuel filter replace them all and clean the mass airflow sensor in the intake tube after the air filter.you need to establish a baseline first before proceeding.

You may have a short to ground meaning your wires are pinched together or you have the lead to one or more of yor devices touching metal. Thats two options the other one is one of your devices may be bad and hopefully this is the case. To test that theroy you will need to have several spare fuses. Start by unplugging one device at a time them inserting a new fuse and keep doing this process until the fuse doesnt blow then you wil have your culpret. If that doesnt work you will need an electrical specialist to track down which part of your wiring is shorting your fuse out. I would try your cigarette lighter and horn first.

Could be exhaust damaged and letting fumes into cabin!

Have you checked the fuse? Do you have power to the switch? Do you have power from switch to regulater? If so than you need to replace window regulater. Of you can hear the window regulater working but the windows isn't moving it could be as simple as some plastic clips. If so remember to clean and lube the tracks.

There are multiple temp sensors on that ,. One is in the MAP sensor and the other is the radiator. What is extremely cold?

it sounds like your heater moter has a short try unpluging it

the grab handel has 2 bolts that need removed i belive they are 5/16 as for the rest of the panel slip a flat bar behind between the door and panel and pry gentle as not 2 break the door panel it is held on by push pins that you can buy at your auto parts store its sounds harded than it is

this model SA rather than SC seems to be a Middle East model. The SC version doesn't have DAB. https://www.google.com/search?q=panasonic+sa-pm250+instruction+manual ..

Question edited for clarity, typo and CAPS. Question moved from Cars and Trucks category. Claim on the warranty irrespective of how long you have had them. They charge $180 but they cost them $20 to buy from China. Package them up and send them tracked and ask them to replace the batteries. How long is the warranty on AfterShokz? While we hope you never need it, all new Shokz purchased from authorized retailers come with a two-year warranty that begins on your date of purchase. Jan 11, 2019

How To File A Warranty Claim For Your SHOKZ Headphones

https://www.google.com/search?q=Openfit+Shokz+battery+replacement ..

1. Power Off: Turn off the device.
2. Jumper Configuration: Locate the jumper labeled "S16" on the device. Initially, it should be connected to pins 2 and 3.
3. Power On (Alarm+All LEDs Flashing): Turn the device back on. You'll see the alarm LED and all other LEDs flashing.
4. Power Off Again: Turn off the device once more.
5. Jumper Adjustment: Change the jumper configuration from pins 2 and 3 to pins 1 and 2.
6. Finished: Your Porpo YH-2000 is now set to the desired angular unit mode.

If you encounter any issues, you can press the reset switch on the back of the device to reinitialize it.

If the display is working, you have audio. Check your amplifier. 1300Watt adaptor ... This unit draws a very low power and that is not needed.

The F2100 remote is not explicitly listed as compatible with the AerialBox T2100, I recommend using the remote that came with your AerialBox T2100 for optimal functionality. If you have any specific compatibility concerns, I suggest reaching out to Dish TV customer support for further assistance.

Are you using the charging cables that came with it? That is a type C. Are you securely attaching the charging cable? A loose connection would keep the battery from charging. If you had a low battery, you would see a red light. That you have no light at all suggests there is no charge left in the battery. I'm not sure the reset will work with no charge which is why you ought to check the cables first. But turn it off and then hold down the Multifunction button for 10 seconds to reset it. Then turn it back on and see what happens. If you can, test the charging cable on aother device. If you have another type C charging cable, try it, just to eliminate a bad cable. If these suggestions don't work, you may try the manufacturer's customer support.

Question edited for clarity, 'make model (what it is)'. The images show the rear connections. It looks like 2 x 1/2" jacks and a multi-pin connector for a sound mixer. I have never heard this term before? Passive stage monitor. Uses speakon connection. It is this

Speakon connector

Wikipedia https://en.wikipedia.org > wiki > Speakon_connector Speakon connectors arrange their contacts in two concentric rings, with the inner contacts named +1, +2, etc. and the outer contacts connectors (in the four- ... The company has disowned it! https://harbingerproaudio.com/manuals/

Harbinger HX121M 12" Stage Monitor

Musician's Friend https://www.musiciansfriend.com > pro-audio > harbinge... 12" loudspeaker featuring a 2.5" high-temperature, precision edge-wound polyamide voice coil and an 80 oz. vented magnet structure.

Harbinger HX 121m Passive monitor

Reverb https://reverb.com > Pro Audio > Speakers > Harbinger Passive stage monitor. Uses speakon connection. ..

All questions need clear 'make model (what it is)' first 3 words. https://www.google.com/search?q=fmdott085+V398 ..

Set Time Hours and Minutes: Press Time/12/24 and Alarm1/ON/OFF buttons at the same time for two seconds and it will start to blink the hour. Press and hold the button for a fast setting or tap it briefly to increase the setting by one hour. Now set the minutes with time (press and hold) and min. How do I set the Audiosonic clock? Set current time Press and hold the time button and simultaneously press the hour to set the hours in 24-hour mode .