First check the dual water valve. If the valve is bad, it will need replacing. Try ordering the recommended icemaker part from AppliancePartsPros. It should arrive in a few days and should take less than 15 minutes to drop in. This new unit should start producing ice in less than 30 minutes.
If you think it is the motor, try Sears Parts direct (put in search engine) and you will get step by step instructions.
Hope this helps,
David
The part that keeps the flapper door closed can break which will let frost to build up. The door itself can break in two. My repair man used crazy glue to fix mine and was done in 5 minutes.
If the ice maker is not refilling with water after its last harvest that points to the=> W10408179 Water Inlet Valve. If the ice maker just sits there with ice and does not empty into the ice bucket we will need to test the 4389102 Ice Level Control Instructions on how to test can be found HERE If you have something else happening here please let me know, Sea BreezeIf the ice maker is not refilling with water the side of the water control valve that fills the ice maker is defective and you will still get water from the dispenser. The parts I listeed above are for your GS6SHAXLS03 refrigerator.
There can be many reasons why your refrigerator is freezing your food. To see what could be happening and to figure out how to possibly fix your problem. Take a look at this tip which contains many of the causes and solutions to fix the problems.
During its manufacturing, the screw is fixed through the handle and then the hole made by that is covered by the material of the handle. You can't do that by your own. If you want it to be perfect, ask the company.
HI, the Ice maker control module will need to be replaced in your unit asap if possible. this module controls and initiates the actions when the lever is depressed.
Your refrigerator has possibly stoped defrosting and this is the symptoms and first signs. The defrost control board is located inside the temperature control panel and usually is the part that causes the defrost to stop. You need to unplug and inspect or defrost your freezer. Have a look at the defrost elements to make sure they are not burned out, The part number for the defrost control is W10135899 Let me know if you have questions or need more assistance . at [email protected] Thanks, Sea Breeze
On the back and near the floor there is a water control valve. One side controls water to the dispenser and the other is for the ice maker. Need to test the one that goes to ice maker first by checking the solenoid coil with an ohm meter or put household voltage to it and it should open and send water up to ice maker. If not there then check the pipe coming into freezer from outside for freezing water in pipe. We will go further when you are ready. Let me know when you are able to do these things, I will be here, Thanks, Sea Breeze
vtdeanda, usually that is a sign that the condensor fan is not running. Could be jammed with something. It sits in the back by the compressor. Check this out first..Catriver..post back
Delete
To replace the LED light in your Whirlpool WRSSDHW08 freezer, follow these steps:
Unplug the refrigerator to ensure safety.
Remove all the items from the freezer to give yourself more room to work.
Locate the light cover inside the freezer. The LED light should be underneath this cover.
Carefully pry the light cover off using a flat-head screwdriver or your fingers. Be gentle to avoid damaging the cover.
Once the light cover is removed, you should see the LED light module. It may be held in place by clips or plugs.
Disconnect the power supply to the LED light. This may involve twisting or pulling the plug from its socket.
Remove the old LED light module from the freezer.
Purchase a replacement LED light module from the Whirlpool website or an appliance parts store. Make sure to get the correct part number for your specific refrigerator model.
Install the new LED light module by connecting it to the power supply and placing it back into its slot in the freezer.
Replace the light cover by snapping it back into place.
Plug the refrigerator back in and test the new LED light.
If you have any trouble replacing the LED light or if you are unsure about any steps, consult the user manual for your Whirlpool refrigerator or contact a professional appliance repair technician for assistance.
The Whirlpool WRB322DMBM01 refrigerator model typically does not have a dedicated water filter for the ice maker. Instead, it relies on an external water filtration system or an in-line water filter that may be installed in the water supply line connected to the refrigerator.
Here's how you can check for and change the water filter for your ice maker:
1. **Locate the Water Supply Line**: Trace the water supply line that connects to the back of your refrigerator. The water supply line is usually a flexible plastic or metal tube that runs from the water source (such as a water pipe or faucet) to the refrigerator.
2. **Check for an In-Line Water Filter**: Look along the length of the water supply line for any inline water filters. These filters may be attached to the water line using compression fittings or push-to-connect fittings. They are typically cylindrical or rectangular in shape.
3. **Inspect the Filter**: If you find an in-line water filter, inspect it to determine its type and condition. Some filters have a label indicating the brand and model number, while others may have a date or indicator showing when it was last replaced.
4. **Replace the Filter (if Necessary)**: If the water filter is due for replacement or is visibly dirty or clogged, follow the manufacturer's instructions for replacing it. This typically involves turning off the water supply, disconnecting the filter from the water line, and installing a new filter in its place.
5. **Flush the System**: After installing the new filter, flush the water system to remove any air or debris. Run water through the dispenser or activate the ice maker to purge the system of any trapped air or loose particles.
6. **Monitor Performance**: Monitor the performance of your ice maker and water dispenser to ensure that the new filter is functioning correctly. It may take a few cycles for the water system to fully adjust to the new filter.
If you cannot find an in-line water filter connected to your refrigerator's water supply line, it's possible that your refrigerator does not have a built-in water filtration system for the ice maker. In this case, you may need to consider installing an external water filtration system to improve the quality of your ice and water.
Check the control panel or display on the refrigerator for any error codes or indicators that might suggest a malfunction. Reset the control panel by unplugging the refrigerator for a few minutes and then plugging it back in.
If the ice maker is not refilling with water after its last harvest that points to the=> W10408179 Water Inlet Valve. If the ice maker just sits there with ice and does not empty into the ice bucket we will need to test the 4389102 Ice Level Control Instructions on how to test can be found HERE If you have something else happening here please let me know, Sea BreezeIf the ice maker is not refilling with water the side of the water control valve that fills the ice maker is defective and you will still get water from the dispenser. The parts I listeed above are for your GS6SHAXLS03 refrigerator.
