20 Most Recent
Kenwood KDC-MP3035 CD Player Questions & Answers
It only says PROTECT, I
If the wires and speakers all check out fine, you probably have a bad output ic or volume control ic.
9/1/2011 9:53:21 PM •
Kenwood...
•
Answered
on Sep 01, 2011
Radio has sound, but cd
do you have a amplifier in the vehicle? if so you may have the power antenna wire (blue) connected instead of the blue/white.
2/19/2011 4:38:02 PM •
Kenwood...
•
Answered
on Feb 19, 2011
How do i put on aux
you need to get into the menu to change this setting, to do so follow these steps.
1. push source until the unit is in standby mode.
2. hold the menu button until it opens the menu.
3. scroll through it until you find AUX 1 or AUX2, which ever one you are using
4. you then should be able to change the setting by using the track buttons or by pushing in the control knob.
once you have changed the setting. the option should now be in your source menu. hope this helps
10/5/2009 3:47:54 AM •
Kenwood...
•
Answered
on Oct 05, 2009
Forgot code to be enterd when first powering up
Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:
KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.
The
procedure to enter your security code differs on various models of
Kenwood car stereos. Here are three of the more common procedures:
Type 1
During
the code request mode, while holding the DISP key depressed, press and
hold the Volume UP or DOWN key for 3 seconds until the "..." display
disappears.
Enter the security code using your Kenwood remote.
Type 2
Press the "Auto" button and "Track up" on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To
enter a letter using your Kenwood remote, press a button once for the
first letter, twice for the second letter, and three times for the
third letter -- then press the Track Up or Next Track key to send the
letter.
To send the letter 'A', press the 2 key once and then
press the Track Up key. To send the letter 'B', press the 2 key twice
and then press the Track up key.
Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.
The key sequence to enter the security code KCAR is:
5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.
A Security Code Bug in some Kenwoods
There
is a reported bug in the security code handling of some Kenwood
stereos. In models with thie bug, the security code is stored
incorrectly. The workaround is to enter the wrong security code.
In
models with this bug, you have to decrement the third character of the
security code by one. If your security code was 1111, you would enter
your security code as 1101. If your security code was 9999, you would
enter 9989.
7/15/2009 6:01:52 PM •
Kenwood...
•
Answered
on Jul 15, 2009
How to set the time
1. Select Clock Adjustment mode by doing this:
Push the control knob towards [FM] or [AM] (unit must be in the stand-by mode, ie: turned off)
2. select the CLK ADJ display
3. To enter clock adjustment mode, press the control knob for at least one second. The clock display will blink.
4. To adjust the hours, push te control knob towards FM or AM.
5. To adjust the minutes, push the control knob towards |<< or >>|.
6. To exit the clock adjustment mode, press the MENU button.
This information was taken from the instruction manual that I was able to find online. Shoot me an e-mail and I'll forward it off to you. (page 20)
1/30/2009 10:35:18 PM •
Kenwood...
•
Answered
on Jan 30, 2009
The "Demo Mode" won't stop!!
Press the Source button until the unit enters Standby mode. Then press and hold the Menu button.
Scrolling through the menu functions, you should come to one that says "demo". Turn it off by pressing and holding the 4-way knob.
11/7/2008 3:46:50 AM •
Kenwood...
•
Answered
on Nov 07, 2008
The aux input will not work
you must go back into the menu and turn on aux otherwise the head unit will not recognise the aux devise that you are trying to plug in
3/25/2008 5:48:27 PM •
Kenwood...
•
Answered
on Mar 25, 2008
How to turn demo off
1. Be sure the unit is in the stand-by mode (ie: turned off)
2. Push the control knob towards FM or AM. Select the DEMO display
3. To set the DEMO mode, do this:
Press the control knob for at least 2 seconds. The demonstration mode alternates between DEMO ON and DEMO OFF.
Although it doesn't say, i would imagine you need to press the MENU button to exit this screen.
This information came from the instruction manual that I was able to download from the internet. Shoot me an e-mail and I'll forward it off to you.
3/9/2008 3:07:55 PM •
Kenwood...
•
Answered
on Mar 09, 2008
Kenwood KDC-MP3035
make sure you have 12 volts into the radio at high volumes mine shuts off when i turn it up over 25 due to power draw
11/19/2007 2:37:47 PM •
Kenwood...
•
Answered
on Nov 19, 2007
Not finding what you are looking for?