Whirlpool GR9FHMXP Top Freezer Refrigerator - Answered Questions & Fixed issues

1)The door gasket on the freezer door helps keep the cold air in and the warm air out. If the gasket is dirty or damaged, it may prevent the door from closing properly, which can lead to frost buildup on your freezer walls. To make sure the door is sealing, slip a dollar bill or a sheet of paper between the gasket and the freezer and then close the door. If the bill or paper pulls free with little or no resistance, the gasket isn't sealing properly. Wipe the gasket with a damp cloth to remove dirt, grease and other residue. If the gasket is damaged, replace it with a new one. Sometimes frost can accumulate on the back panel of your freezer if the door is open too long or too often. When you open the door, you let warm, humid air inside, and this condenses and freezes. Make sure there are no packages preventing the door from fully closing, and limit how often you open the door by removing what you need all at once. 2)Ventilation is important because it ensures your freezer stays cold. If something inside the freezer blocks the internal vents, the freezer may become warm, causing condensation to form on the walls, and eventually leading to frost buildup. When loading your freezer, make sure there are no items resting against the rear wall of the freezer and space the contents out as much as possible to improve ventilation. 3)Side-by-side refrigerators with a built-in ice maker may accumulate frost if the flap on the ice dispenser doesn't close properly. This allows warm air to enter the freezer side, condense and freeze, causing frost buildup over time. Open the freezer door and examine the flap inside the ice chute. It should be flush against the housing. If it is not, empty the ice bin and make sure there is no ice or debris preventing the flap from closing. 4)If your freezer door closes properly and nothing is keeping it open, frost buildup on the back panel may indicate a problem with the freezer's self-defrost system. The self-defrost system turns off the compressor for a short time every six to 12 hours so it can turn on the defrost heater. This melts any frost buildup on the freezer coils, and the water drains to the pan beneath the freezer. If this component fails, frost continues to build. Move the contents to another freezer and turn your freezer off for 24 to 48 hours to manually defrost the interior. If frost builds up again, contact a qualified appliance repair technician to inspect the defrost timer and repair the problem.

SOUND'S LIKE U HAVE A CLOGED DEFROST LINE OR DRIANE ?

yes that's the drain,it goes down the back to the drip pan near the compressor,the heat will evaporate the water,i use a steamer to clean out the drain, just blow out the line and then pour a cup of hot water down the drain to make sure it's open,some refrigerators have a piece on the back that you can remove and clean out,i'm not sure if you have this,there's a heater probe that you can get that raps around the heater and then sticks into the drain so this doesn't happen again,when the heater comes on the probe also heats up, as long as the drain goes straight down,if it turns as sonn as you stick something in it you can't use the probe

A leaky door gasket will allow excess moisture in and it will condense on the cold surfaces and can also cause excess frost on the evaporator coil causing more water to go into the drain pan.
A good gasket will hold a dollar bill securely all away around the door.

i have the exact same problem...anyone??? now my fridge won't get cold at all and the freezer is still frozen

Check the control panel or display on the refrigerator for any error codes or indicators that might suggest a malfunction. Reset the control panel by unplugging the refrigerator for a few minutes and then plugging it back in.

The Whirlpool WRB322DMBM01 refrigerator model typically does not have a dedicated water filter for the ice maker. Instead, it relies on an external water filtration system or an in-line water filter that may be installed in the water supply line connected to the refrigerator. Here's how you can check for and change the water filter for your ice maker: 1. **Locate the Water Supply Line**: Trace the water supply line that connects to the back of your refrigerator. The water supply line is usually a flexible plastic or metal tube that runs from the water source (such as a water pipe or faucet) to the refrigerator. 2. **Check for an In-Line Water Filter**: Look along the length of the water supply line for any inline water filters. These filters may be attached to the water line using compression fittings or push-to-connect fittings. They are typically cylindrical or rectangular in shape. 3. **Inspect the Filter**: If you find an in-line water filter, inspect it to determine its type and condition. Some filters have a label indicating the brand and model number, while others may have a date or indicator showing when it was last replaced. 4. **Replace the Filter (if Necessary)**: If the water filter is due for replacement or is visibly dirty or clogged, follow the manufacturer's instructions for replacing it. This typically involves turning off the water supply, disconnecting the filter from the water line, and installing a new filter in its place. 5. **Flush the System**: After installing the new filter, flush the water system to remove any air or debris. Run water through the dispenser or activate the ice maker to purge the system of any trapped air or loose particles. 6. **Monitor Performance**: Monitor the performance of your ice maker and water dispenser to ensure that the new filter is functioning correctly. It may take a few cycles for the water system to fully adjust to the new filter. If you cannot find an in-line water filter connected to your refrigerator's water supply line, it's possible that your refrigerator does not have a built-in water filtration system for the ice maker. In this case, you may need to consider installing an external water filtration system to improve the quality of your ice and water.

Delete To replace the LED light in your Whirlpool WRSSDHW08 freezer, follow these steps:

1. Unplug the refrigerator to ensure safety.
2. Remove all the items from the freezer to give yourself more room to work.
3. Locate the light cover inside the freezer. The LED light should be underneath this cover.
4. Carefully pry the light cover off using a flat-head screwdriver or your fingers. Be gentle to avoid damaging the cover.
5. Once the light cover is removed, you should see the LED light module. It may be held in place by clips or plugs.
6. Disconnect the power supply to the LED light. This may involve twisting or pulling the plug from its socket.
7. Remove the old LED light module from the freezer.
8. Purchase a replacement LED light module from the Whirlpool website or an appliance parts store. Make sure to get the correct part number for your specific refrigerator model.
9. Install the new LED light module by connecting it to the power supply and placing it back into its slot in the freezer.
10. Replace the light cover by snapping it back into place.
11. Plug the refrigerator back in and test the new LED light.

If you have any trouble replacing the LED light or if you are unsure about any steps, consult the user manual for your Whirlpool refrigerator or contact a professional appliance repair technician for assistance.

https://www.appliancepartspros.com/repair-help/whirlpool-refrigerator-wrf535smbm00-repair/wrf535smbm00-ice-maker-not-making-ice.html Whirlpool Refrigerator WRF535SMBM00 Ice maker not making ice Causes of a bad icemaker cycling thermostat can include electrical malfunctions, temperature sensor issues, or wear and tear. Symptoms of a bad icemaker cycling thermostat may include: Inconsistent ice production. The icemaker not cycling properly.

HOW-TO: Whirlpool Refrigerator WRF535SMBM00 Ice maker ...

There is no water filter.

Where is the filter for water for ice maker located on

JustAnswer https://www.justanswer.com > Appliance Repair Jul 23, 2018 - This particular model does not have a filter built into it so that is why you can't find one. If you wanted to add a filter, you can get an in- ...

See page 11 troubleshooting of manual. This problem is discussed there. Whirlpool GS5VHAXWY - 25.6 cu. Ft. Refrigerator Use And Care Manual (Page 11 of 37) ' ManualsLib

Click on Part 20, Bi-Metal Defrost. I have never seen one like this before! https://www.partselect.ca/Models/WRT549SZDM01/Sections/Liner-Parts/?ModelID=7185057&ModelNum=WRT549SZDM01&mfgModelNum=&ManufactureID=3&Selected=28E07ECB18AF9AC514E92A1E4DCDBD928C532352&Position=4&mfg=Whirlpool&Type=Washer&Mark=4 ..

If it has a defrost timer, some are adjustable. If not just replace it. https://www.google.com/search?q=Whirlpool+freezer+defrosting+too+often ..

Question edited for clarity, spelling of maker, toss in a load of CAPS. Question moved from Cars and Trucks. Yes they do. https://www.google.com/search?q=whirlpool+et1mtkxkq20 ..

Question turned around for clarity. Whirlpool sell spares including wire baskets https://www.whirlpoolparts.com/Shop-For-Parts/a3b5i554-x676435736861/Gd5sha-Whirlpool-Freezer-Basket-Parts Or places like this https://www.appliancepartspros.com/search.aspx?model=gd5sha ..

Question edited for clarity Zeros (0) and ohs (o) aren't interchangeable in serial numbers :>D If icemakers are going wrong it is best just to replace the complete icemaker unit. They work in a very hostile environment or cold, wet, electricity and limescale and bio-slime. Some commercial icemakers I have witnessed in catering facilities would have you never taking ice in a bar or restaurant again! https://www.google.com/search?q=Whirlpool+MFI26665XEW3+parts ..

As the freezer is working you can probably discount that the reason is low refrigerant gas. The other reasons would be that the fridge circulation fan has failed. or The channel that directs cold air from the freezer is blocked with ice at the rear of the freezer. It happened to my GE and was caused by a failed defrost timer that was icing up the evaporator coils at the back of the freezer. A service call lasts about an hour including melting the ice with a heat gun..

Remove the ice build up at the back of the drawer or something may have fallen over the top edge.. To remove the drawer, lift at the front and pull, or look on the side rail for catches. Please always include full 'make model (what it is)', then we can refer to the owner or service manual.

A clue to what the faults were may help you get an answer.

I would seriously NOT recommend doing this! Trying to run a 110 volt appliance at 220 volts is too much power for the electrics inside the refrigerator (or any 110v appliance) to cope with. You will 'Fry' the electrics possibly even risking causing a fire. Do you have a model or serial number for this refrigerator? You might have to see if you can source one online and import it from the US. That could get expensive! A simple and obvious answer here if the part is so difficult to get, is to buy a whole new refrigerator. Compare the cost of both options as it may be cheaper to replace the whole appliance.

There are several causes for a refrigerator that doesn't cool, including dirty condenser coils, poor ventilation, improper installation, faulty or dirty gasket seals, unorganized food storage, appliance location and malfunctioning internal parts.