20 Most Recent RCA 20F420T 20" TV - Page 8 Questions & Answers

If you are unable to receive channel 526 or 54 on your RCA HDMI TV and the picture goes pixels or freezes, it may be caused by a few different issues:

1. Check the cable connections on the back of the TV and the cable box or streaming device to ensure that all cables are securely plugged in and the devices are properly connected.
2. Check the settings on your TV and cable box or streaming device to make sure that they are set to the correct channel and that the channel is not blocked or set to a different input.
3. Check the signal strength of the cable or streaming service, if the signal strength is low or poor, it can cause picture issues like pixels or freezing.
4. Check for any physical damage to the cables, if the cables are damaged, it can cause picture issues.
5. Try to scan for channels on the TV and cable box or streaming device to ensure that all channels are being picked up properly.
6. If the problem persists, contact your cable or streaming provider for further assistance, as the issue may be on their end.
7. If the problem is not resolved, you may want to contact RCA customer service for further assistance.

It's important to note that in some cases, the channels you're trying to watch may be experiencing technical difficulties, or the channel is not available in your area.

Hola buenas los c?digos del televisor challenger gracias

It sounds like you are having difficulty getting a signal from your satellite receiver on your RCA ColorTrak Plus TV. There are a few things you can try to troubleshoot the problem:

1. Make sure that all of the cables are properly connected between the satellite receiver and the TV. Double-check that the yellow, red, and white cables are securely plugged into the correct inputs on the TV.
2. Check the settings on the satellite receiver to make sure that it is set to output to the correct input on the TV. Consult the user manual for your satellite receiver for instructions on how to access and change the settings.
3. Check the settings on the TV to make sure that it is set to the correct input. This can usually be done by pressing the "Input" or "Source" button on the TV's remote control.
4. Check the satellite receiver's LNB (low noise block downconverter) and make sure it's pointed at the satellite.
5. If the above steps don't work, try resetting both the satellite receiver and the TV to their factory default settings. This can often resolve issues with the TV not receiving a signal.
6. If you are still having issues, it's possible that the TV's tuner is not compatible with the satellite signal, or the TV's tuner is malfunctioning. In this case, you may need to consider getting a separate satellite TV tuner and connecting it to the TV.
7. If you've tried all the above and still having issues, it's best to contact the manufacturer of your satellite receiver or TV for further assistance.

It's important to note that the setup and troubleshooting process may vary depending on the specific model of your TV, satellite receiver and antenna. Also, if you are not comfortable with troubleshooting electronic devices, it's best to contact a professional technician to do the job for you.

You can't use a Sanyo Remote to control a Vizio television. They are one channel, one device. You need a Facsimile Remote or a Vizio original made for the television. https://www.fixya.com/support/r29872378-universal_remotes_no_facsimile_remote ..

Your RCA LED50B45RQ TV appears to have a problem with the display and audio. When the TV is turned on and the remote is used, the standby light illuminates, and the screen flashes white on the left side without audio or video. Various factors could be to blame for this problem. A few troubleshooting tips are provided below:

1. Check the connections: Make sure that all the connections between your TV, cable box, or streaming device are securely plugged in.
2. Check the settings: Ensure that the TV is set to the correct input and that the cable box or streaming device is set to the correct output.
3. Check the backlight: Some TVs have an adjustable backlight setting. Ensure the backlight setting is turned on and set enough.
4. Check the cable: If the cable that connects the TV to the wall outlet is damaged, the TV won't turn on. Try unplugging the TV, waiting a few minutes, and plugging it back in.
5. Check the power supply: The power supply could be malfunctioning. It could be damaged or not provide enough power to the TV.
6. Check the Main Board: The main board controls all TV functions. It could be malfunctioning, which is causing the TV not to turn on or display correctly.
7. Contact the manufacturer: If none of the above solutions work, it may be necessary to contact the manufacturer for further assistance. Your TV may require repair or replacement.

Use Roku Accessibility Settings You can also turn off narration on your Roku from the Accessibility options. From the Roku Home screen, go to Settings > Accessibility. Under Audio Guide, select Audio Guide or Screen reader. Highlight Off to disable this feature.

Failing power supply

Tv boards are fairly easy to replace. usually there are 2. one is the power board. should be obvious to see as the wire that plugs into the AC wall outlet is connected to it. The other will be the one your needing. Look on the board and find the part number. Then the search begin. Let me know if i can help further.

If your RCA TV is not displaying color in the apps, there are a few potential causes and steps you can try to fix the issue:

1. Check the TV's color settings: Make sure the TV's color settings are set correctly. You can try adjusting the color settings to see if this fixes the problem.
2. Check the HDMI connection: If you are using an HDMI cable to connect the TV to a device (such as a cable box or streaming device), make sure the connection is secure and the HDMI cable is not damaged.
3. Restart the TV: Sometimes a simple restart of the TV can fix minor issues. Try turning the TV off and on again to see if this fixes the problem.
4. Check for software updates: The TV may need a software update to fix the issue. Check for updates and install any available updates.

If these steps do not fix the problem, there may be an issue with the TV itself or with the device you are using to access the apps. In this case, it is recommended to contact RCA customer support or a TV repair technician for further assistance.

Hey Tony, there are 2 things that can cause the issue your seeing, I want to double check one thing, when you say the standby light is on you mean it stays on, it stays on steady and doesn't blink, when you push the power button on the tv? If it blinks we need to go down another road however this model and many other models of Funai brand sets have main board issues, it's possible your power supply is bad however if you're getting standby voltage and you are if you see a standby light that means the hot side of the supply is working and that's where about 90% of power board issues are. Go to shopjimmy.com and put the model number of the main board in the search and see if one is available, as a last resort look on ebay but I don't advise buying boards there. Hope this helps, one other thing, if you can't fix it yourself you might as well recycle it as taking it in for service will run close to the cost of a new set.

If the codes for your Digital Lab DLU-5004B universal remote are not working with your RCA TV, there are a few things you can try to troubleshoot the issue:

1. Check the manufacturer's website: Some manufacturers may have updated or additional codes available for their TVs. You can check the manufacturer's website to see if there are any new codes that may work with your TV.
2. Try a different code: If the codes provided in the remote's manual are not working, you can try using a different code for your TV brand. You can find a list of codes for different TV brands online or in the manual for your universal remote.
3. Check the remote's battery: Make sure the remote's battery is charged and properly installed. A weak or dead battery can cause the remote to malfunction.
4. Reset the remote: Resetting the remote may help resolve any issues with the remote's programming. To reset the remote, remove the battery and press any button on the remote for at least 15 seconds. Then, reinsert the battery and try the codes again.
5. Check the TV's compatibility: Some TVs may not be compatible with universal remotes, in which case you will need to use the TV's original remote or a different universal remote that is compatible with your TV.

If these troubleshooting steps do not resolve the issue, it is possible that there is a problem with the remote or the TV itself. In this case, it is recommended to bring your TV and remote to a professional for further diagnosis and repair.

Television resolution, it will produce 1080i or 480p using the component input jacks. No way as sharp as 720p. This is of course dependent on your cable provider ..

There isn't one! Televisions, DVD and Set top boxes only. You buy a replacement Crossly remote from the maker. https://www.google.com/search?q=crossly+I+juke ..

I assume "pilot light" is the standby light you're referring to. On most Funai brands including RCA, a continual flash of the standy light indicates inverter shutdown, pointing to bad LED backlights, new ones can be ordered from shopjimmy.com and you can install them yourself, no special tools are needed, however watch a couple youtube vids to see some tips on how to do it.

RCA remote control have no set-up code to Ilive brand devices. To select a proper universal remote control, you should know about the number of digits to its set-up codes. There are 3 digit, 4 digit, 5 digit, 2 digit and even single digit codes, to some brand devices. After confirming this, check the sites linked here. Both the sites have set-up code list and set-up procedure to many popular brand remote controls. Check which brand remote control has set-up code/s to your device brand, and buy that one according to availability? Brand name of the remote control isn't a matter, but it should have set-up codes in its code list, to the device brand you have. Please note: Every new universal remote control will have set-up code list, and set-up procedure along with its pack. Never accept a remote control, that hasn't both of this. For more details about the set-up codes, visit the site http://electrohelponline.blogspot.com/ Check this site too. http://remotesearch.blogspot.com/ Universal remote controls are available at most of the electronic spare part selling shops. Visit some online sites too, which deals with electronic spare parts.

If you have an RCA 26211 remote, you can program it to control a DVD player by following these steps: 1. Press and hold the "Setup" button on the remote until the red light on the remote blinks twice. 2. Enter the code "9-9-1" on the remote. The red light will blink twice. 3. Press and hold the "DVD" button on the remote. The red light will blink twice. 4. Enter the code for your DVD player on the remote. The code will be four digits long. 5. Press the "Power" button on the remote. The DVD player should turn on. You can find the code for your DVD player in the manual that came with the player, or you can look it up online.

RCA RV-9978 User Manual ' 28 pages - manualsdir.com

https://www.manualsdir.com > ... > RV-9978 User guide • Read online or download PDF • RCA RV-9978 User Manual • RCA Receivers and Amplifiers.

RCA Service Menu Instructions In order to access the service menu on your RCA TV you will need to have a remote, if your remote is lost or damaged we recommend that you purchase a Replacement Remote before trying to access the service menu on your set. Method 1

1. Press the INPUT button on the remote.
2. Then press the 2, 5, 8, 0 buttons in quick succession.

Method 2

1. Press the MENU button on the remote.
2. Then press the 1, 1, 4, 7 buttons in quick succession.

Categories:

• RCA
• Service Menu