20 Most Recent Ariston Technologies AW129NA 16 Lbs Front Load Washer - Page 9 Questions & Answers


see this causes and fix it. God bless you
F05 Water temperature sensor error If during the water heating step in the wash cycle, the water temperature sensor (NTC) value is out of range, or the heating element circuit has failed, the F05 error code will be displayed.

Potential Causes

• Check the Water Temperature Sensor, Heating Element and Element Relay
• Check connections to the Sensor, Heating Element and Relay

Replace failed component.

Ariston... | Answered on Sep 30, 2012


see the causes and use the common sense, God bless you.
If your washer won't drain, check these: It spins, but doesn't pump It doesn't spin or pump It pumps, but the water returns It spins, but doesn't pump If your washer spins but doesn't pump the water out, the drain line is probably clogged. In many washers, a small sock or other piece of clothing can get between the clothes tub and the outer tub that holds the water. If the clothing gets between the tubs, it may then get into the drain hose that's attached to the pump--or even into the pump itself. If it's in the pump, you need to remove the hoses from the pump and pull the item out. To remove the sock from the outer tub port, open the washer's main access panel and remove the large-diameter rubber hose that connects the pump to the bottom of the outer tub. Then, using needle-nose pliers, try to grab and remove the clothing through the port. Sometimes you can't remove the stuck clothing from below. Then you have to remove the agitator, top of the outer drum shield, and inner clothes tub. This isn't easy to do--and you may need special tools--so you might be happier getting a qualified appliance repair technician to do the job. If the drain line isn't plugged, the problem may be with your pump. Even if the pump appears to be turning, the internal impeller may be broken. If so, you need to replace the pump. It doesn't spin or pump If your washer doesn't spin or pump water out but the motor is running, your washer probably has a frozen pump pulley. If so, you need to replace the pump. To check the pulley, remove the pump from the washer and try to rotate the pulley manually. If it doesn't turn freely--if it's frozen or stiff--replace it. It pumps, but the water returns If the water that pumps out of the machine goes back into the machine after the spin cycle, your washer may be siphoning the water from a laundry tub that has a slow drain, back into the washer. The usual remedy for this is to improve the draining of the laundry tub. (Is something stuck in the drain?) Also, check for these problems: If the drain hose reaches more than about 4 inches into the laundry tub, cut off the excess. If your drain hose is lower than the washer's cabinet, install an air gap/siphon break assembly.
9_20_2012_3_18_26_am.jpg9_20_2012_3_22_09_am.gif

Ariston... | Answered on Sep 20, 2012


There is a motor, located under the main switch, that drives the switch. It is probably bad. murf427

Ariston... | Answered on Aug 30, 2012


I Had the same problem and had to change out the timer dial. hope that get's you in the right direction.thanks,toby

Ariston... | Answered on Jun 07, 2012

Not finding what you are looking for?
Ariston Technologies AW129NA 16 Lbs Front Load Washer Logo

23 questions posted

Ask a Question

Usually answered in minutes!

Top Ariston Technologies Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Harrie

Level 3 Expert

6746 Answers

ray gallant

Level 3 Expert

71004 Answers

Are you an Ariston Technologies Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ariston Technologies Washing Machines

  • Ariston Technologies Washing Machines

Most Popular Question

washing machine door will not open

  • Washing Machines
Loading...