20 Most Recent
Ariston Technologies AW129NA 16 Lbs Front Load Washer - Page 3 Questions & Answers
1 Answer
Drive belt
I am supposing you are wanting a drive belt for your machine. Please type in "Ariston" on your search engine, as I did, and you will find that you can call them for your answers to your problems.
After a little looking, I found them in about 4 minutes.
God bless your efforts.
Ariston...
|
Answered
on Jan 05, 2016
1 Answer
Avtxf 149 f-08
F08 - Heater relay cannot be activated
- Check wiring
- Check pressure switch and connections
- Tap relays as they can jam on new boards
- Check electronic control PCB
- Check heating element
Dado
Ariston...
|
Answered
on Oct 11, 2015
1 Answer
Axvf120rr f10 error
F10: Pressure Switch Empty and Full or neither Empty nor Full
Pressure Switch Found
Overhaul CN1
Overhaul Pressure Switch Wiring
Control CN1/Pressure Switch Continuity
Replace Pressure Switch
Replace Card
Dado
Ariston...
|
Answered
on Oct 06, 2015
1 Answer
I have a code H 20 then it goes to F01
The washing machine fails to load water (The wording H20 is
displayed).
• The water inlet hose is not connected to the tap.
• The hose is bent.
• The water tap is not turned on.
• There is a water shortage.
• The water pressure is insufficient.
• The START/RESET button has not been pressed.
F01: Triac Short circuit
Overhaul CNE
Replace Card
Dado
Ariston...
|
Answered
on Oct 06, 2015
1 Answer
Ariston washer/dryer arwdf129na
F04: Overflow and Pressure Switch Empty found at the same time (Pressure Switch stuck on Empty)
Overhaul CN1
Overhaul Pressure Switch Contacts
Control CN1/Pressure Switch Continuity
Replace Pressure Switch
Replace Card
Dado
Ariston...
|
Answered
on Oct 06, 2015
1 Answer
Why is h20 sign popping up
The washing machine fails to load water (The wording H20 is displayed).
- The water inlet hose is not connected to the tap.
- The hose is bent.
- The water tap is not turned on.
- There is a water shortage.
- The water pressure is insufficient.
- The START/RESET button has not been pressed.
Dado
Ariston...
|
Answered
on Oct 06, 2015
1 Answer
Having a problem with our washing machine, it will not engage in teh apin cycle
F01 - Electronic circuit board fault
Issue: Washing machine is not operating - some or all functions are not selectable.
Cause: Main module, triac on board damaged or components feedback fault
Advice: We recommend you disconnect (unplug) the appliance from the mains supply for a minimum of 2 minutes. Reconnect supply and wait 30 seconds and try starting the machine again.
Dado
Ariston...
|
Answered
on Oct 05, 2015
1 Answer
Ariston ARF 105 H2O error!
I had this issue also and it was because I started the machine and had not turned on the water to it. However, it cleared when I unplugged the power cord, waited about ten seconds, then plugged it back in. I guess they need a "reboot" once in awhile, like a computer - at least mine did. Hope this works for you, too.
Ariston...
|
Answered
on Sep 05, 2015
1 Answer
Aquatis AQXXF 129 h. what is the error code 08?
It means "heater relay cannot be activated". Troubleshooting guide says to tap the relays to try to unjam them. If that fails, replacement of the main control board is necessary. These washers apparently have a propensity for stuck relays on the newer units.
Ariston...
|
Answered
on Aug 17, 2015
Not finding what you are looking for?
