20 Most Recent Ariston Technologies AW129NA 16 Lbs Front Load Washer - Page 2 Questions & Answers


Hi,
Search "ifb error codes" alternatively substitute ariston for ifb.

Ariston... | Answered on Sep 22, 2018


when I wash heavy stuff it will not spin properly because the weight is not distributed evenly over the load and it stops every time. you may need a repair man unless you can just move the dial to a drain spot rather than spin, if enough water gets out it will probably open then.

Ariston... | Answered on Jun 15, 2018


Has anyone got manual for ariston K-LB 121?

Ariston... | Answered on May 02, 2018


H2O is the symbol for WATER and probably indicates a WATER related fault on your machine. A pressure switch is the normal way the machines 'sense' when the level is sufficient. Overfilling suggests a faulty switch, which will need to be replaced by a technician. Also, ensure that the machine drains as it should, if not, the pump filter may be blocked.

Ariston... | Answered on Apr 04, 2018


Before you change fuses, do you have an internal fuse board or RCD system in your home? Sometimes, an individual RCD can trip out, locking off sockets. Some sockets are individually set up for up and downstairs in a house, or different rooms. If you have a board or RCDs, check them out :)

Ariston... | Answered on Nov 18, 2017


This is normal , it takes small quantity of water unlikes old washing machines

Ariston... | Answered on Oct 04, 2017


Washer fills with water and overflows:

The water pressure level switch is a pressure activated switch that is used to determine the correct water level in the tub. This part is normally located behind the control panel and will have a hose or air dome tube that connects it to the tub. On washers that use an electronic control, this switch may be located at the sump area below the tub. As the water fills in the tub it will compress the air in the tube and push against a diaphragm inside the switch. The switch will control the water inlet valve and turn the valve off at the correct water level. If the tube has a leak, not enough pressure may be created to activate the switch and the washer may overfill. If the switch is defective it may also cause the machine to overfill. To determine if the switch is bad, you should first eliminate the air dome hose as a problem. Look for signs of cracks or worn areas on the hose. Remove the hose and submerge in water. Seal one end and blow air into the other end and look for bubbles. Check for an obstruction in the hose as well. If the air dome hose appears to be ok, then the water level switch may be defective.

You can test it with a meter and with a manual test? ( first locate it in the panel, it has a plastic clear tube hose going into it, remove that tube from its connection, now put another small tube or hose into the slot where it was and have the machine set to wash cycle with water in it. Blow into the other end of the tube.
If the machine starts to wash. the pressure switch is more than likely good
( No wash- then THE DIAPHRAGM IS BAD AND SWITCH HAS TO BE REPLACED).

The other item to check would be your water inlet valve. Check it for continuity with a multi meter it should show Ohms or a closed circuit. To test it when water is overflowing unplug the unit and see if it still overflows or continues to fill. If it stops when unplugged. Then it is not a water inlet problem but an electrical signal problem going to ur water inlet valve. Possibly from the panel or board. You can also do a live volt test to see if it is getting the full 120 current, but be sure to unplug unit before testing as this is a live test.
Also another trick to check the water valve, is to first cut the water off and remove the hoses off the back of the washer. Then one at a time point the hoses inside the washer tub and turn the water back on. If you don't have good water pressure, turn the water back off and remove the strainer that should be in one end of the hose. Inspect the strainer to see if it is stopped up, clean it and reinstall it. Now repeat this test. If you have good water pressure now, reinstall hose and your problem is fixed

By the way my advice is free cuz God is good!




Ariston... | Answered on Dec 08, 2016

Not finding what you are looking for?
Ariston Technologies AW129NA 16 Lbs Front Load Washer Logo

23 questions posted

Ask a Question

Usually answered in minutes!

Top Ariston Technologies Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Harrie

Level 3 Expert

6746 Answers

ray gallant

Level 3 Expert

71004 Answers

Are you an Ariston Technologies Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ariston Technologies Washing Machines

  • Ariston Technologies Washing Machines

Most Popular Question

washing machine door will not open

  • Washing Machines
Loading...