Top 20
Miele 36 in. KM3474 Gas Cooktop Questions & Answers
CAN YOU GET THE GLASS
Hi anina266,
It comes with the trimming unfortunately.
Part number: 23022302
Kind Regards
JEDEMEYER1
* If this solution helped you, please rate it
I have looked all the site for MIELE parts, but
you can only purchase Miele parts from Miele and no one else other than authorized Miele service agents and it is the same price. you would also have to call them as parts are not on line
Miele KM 3474 stove top lights but turns off after 30 seconds
Does the burner attempt to re-ignite after it goes out? If so, it's probably the therocouple. If not, it could be the burner valve. Be sure the caps and rings are correctly seated on the burners and be sure to firmly press the burner knob down to start the flame.
Miele HR1124 cooktop - turning one burner on keeps igniter clicking for all 4 burners.
It is a gas appliance and it is a Miele, so you need a registered gas technician to service it. In my experience, the spark igniters work on all burners. To clean the burners, remove them all and put them in a large saucepan. Add cold water and dish liquid, bring slowly to a simmer and turn off. When cold, rinse and scrub with a plastic pot brush, paying particular attention to holes and slots. This was a job we did in the restaurant every week. It is a good plan to do before you go to bed for the least disruption.
The product specs says;
Automatic re-ignition
•
Sealed burners
•
M Pro Dual Stacked Burner System
So perhaps my hack won't work if they aren't removable.
I found this video :>)
https://blog.yaleappliance.com/new-miele-hr1124-30-inch-professional-gas-range
..
Miele KM-493 induction stove. What does error E13 indicate?
- Error code E13 error showing on display
- What causes an E13, E 13 error code on the Induction Cooktop control panel?
- Error code 13 on Induction Cooktop control panel
Cause:
- Universal OFF key failure
Troubleshooting:
- If the controls are wet or water made contact with them, dry off the controls.
- Turn off then back on to reset.
- If the error persists, reset the unit at the circuit breaker.
- Turn the unit back on to see if the error code cleared.
6/26/2021 12:24:35 AM •
Miele Cooktops
•
2,455 views • 0 helpful votes
Miele induction stovetop dE error?
Miele cooktop induction KM 6350, 6380, 6382, 6383 dE mode
How to switch off demonstration mode
Press ‘power’ button on front and ‘lock’ bottom at same time until you get p5 mode displaying ( it is in programming) mode.
Then press top left to ‘0’, bottom left panel to ‘0’, then press right bottom panel to 9, then press on ‘power’ button to save. This should take it off demonstration mode.
5/15/2018 11:29:21 PM •
Miele Cooktops
•
26,658 views • 4 helpful votes
We can not turn on stays locked ;we have an Miele induction cook top
https://www.coolblue.nl/en/advice/errors-miele-induction-cooktops.html
How do I unlock
my Miele cooktop
? Just under the lock light you should be able to press/hold with your thumb for about 5-15 seconds and it should reset. You may need to place your thumb directly over the lock light or just below it and hold it for that time.
Just under the lock light you should be able to press/hold with your thumb for about 5-15 seconds and it should reset. You may need to place your thumb directly over the lock light or just below it and hold it for that time. If this doesn't unlock when you do this then you have a problem with the control board.
My miele electric cooktop will not stay on after I trip the circuit.
Without more info this is difficult to answer. I will say that all cooktop's have thermal overload switches built into them. They open the circuit until it all cools down and they then close the circuit and reset. You begin using it again and bang it opens again and no power. This means you have a short circuit or a bad overload switch. If you are tripping the circuit breaker, you likely have a short circuit, which is why it is tripping the breaker. I would not keep resetting it, if this is the case. The more you blow or open the breaker the weaker it becomes. They open to prevent an electrical fire, which you do not want.
I have. glass top Miele induction. It keeps flashing 'de';... and will not work. Any idea how I can make my hot top work again?
Bummer deal! While that code response is not known by me, sometimes when a heat sensor fails, or a wire loses contact, the computer gives a code. Be care wiggling any live wires as a weak or broken wire will spark brilliantly. That spark may end the problem - or indicate that part is needed. A sensor sends signal to turn off or on the flow of electricity to control heat levels. When they fail, or a wire closes connection the computer does not know what to do, so it says, "Da," check this thing out, giving the code you see. Pursuing the checks stated will show which problem you have. Hope this works - as those sensors on electric rangers and ovens, wires, and sometime a wire break on the top, or plug-in point for elements are big trouble makers.
PS: Some knobs have a sensor in them that can fail. Of course an appliance person will check each point and may have the code interpetation.. A Tech visit cost about $75 for an estimate.
Not finding what you are looking for?