20 Most Recent
Haier HWD1000 - Page 3 Questions & Answers
Keeps saying error 2 , i have checked the filter
Hi from retired Englishman in SW France,
Following are my generic/standard instructions for filters and drain pump checking. The bit on the pump is near the bottom ;-0)
----------------------------------------------------------------------------------------------------------------------------------------------
Sorry but I do not know your particular machine BUT I would suggest as a first step that you clean the drain motor lint tray/filter. So many 'faults' are caused by blocked filters. The motor is unable to drain all of the water in the allotted time.
If you are unsure where the filter is, it is normally behind the front lower (kick) panel (or in some machines at the rear in an awkward position!) and held in by a round cover/knob.
REMOVE POWER AND ENSURE YOU HAVE A WATER RECEPTACLE/RAGS TO SOAK UP THE WATER WHICH IS BOUND TO POUR OUT!
It's surprising what people have found in theirs! It is always worthwhile checking it on a regular basis.
Now- whilst the filter is removed it is normally possible to see the drain motor and ensure it is not jammed by a foreign object such as a needle or a toothpick. It should be able to be turned by hand/finger- the power IS OFF!
At this point it is also possible to test if the motor works. No clothes or water in the machine, select a spin cycle and put the power back on. You should be able to see the motor turning at some point, possibly straight away. If it doesn't work then the motor is malfunctioning!
Hope the filter is the problem and good luck!
John C
My Haier HWD 1000
There is a button and debris trap on the front bottom right of machine.
Little door says push. Open it and undo the large screw plug.
Remove debis if any. Screw the plug closed until it is very tight.
Check for leaks on next wash cycle.
(Also check intake hose connections at back of machine.)
I have really bad smells coming from the filter
A few tablespoons of vinegar in the middle (fabric softener) compartment of the soaps drawer every few loads should help with any smells.
You could add some diluted bleach to the soap and fabric softener compartments and wash something you don't mind getting bleached. It should kill off any mould or mildew that may have build up in the nooks and crannies. Open the button trap door and clean it out as well (front lower right corner - says push and has a large screw plug inside. Close really tightly after or it will leak)
Dryer Problem
EC4 The temperature of air vent
Within 30 minutes of dry cycle there is 5 minutes in which the temperature is not increasing.
You need to call for repairs. Probably the heating element is faulty.
You can create a custom program without a dry cycle and hang dry your clothing.
Help!!! water leaks from hose of my new haier hwd1000!!!
If water is leaking from the pressure hose itself, go buy new hoses at the hardware store.
If it is the connection between the hose and the machine, you can add hose gaskets and wrap the threads twice in plumber's tape. This is a thin white slightly stretchy tape that you wrap around the threads before you screw on the connector.
I bought the product a
Manual is located here for Haier HWD1000"
http://www.haieramerica.com/fr/product/HWD1000
Click the link that says Product Manual PDF
Error 4 ON HAIER WASHING MACHINE.
Error U04 means the door is open.
Put your knee against the door handle and press it against the handle until you hear a click. The machine should start filling within a minute.
This is a problem I had start occurring about a month after I started using the machine. You will soon do this for every load, a minor annoyance on a cheap machine.
--------------------------------
Error EC4 refers to the temperature of the air vent.
Within 30 minutes of dry cycle there is 5 minutes in which the temperature is not increasing.
Ask the technician to
repair it.
Alternatively make a custom cycle with no drying cycle and hang dry the laundry. I usually do this myself as opposed to listening to it groan for 2-3 hours.
On my Haier HWD1000, I keep getting error message
Error E11 means either:
The water level can not
reach the reset water level
within 5 minutes
OR
The water level can not
reach the setting water level
within 8 minutes
What this means is check your water supply for sufficient pressure and if for some reason it stops and starts (eg. well drawn water with a small reservoir sometimes.)
You may have to make sure that there are no other water uses going on at the same time.
Haier Washer/Dryer HWD1000 water leak
The leak is coming from the pump (part #WD-5470-18) either through the pump inlet and outlet hoses. Disconnect power to the washer and check the pump.
Remove the screws attaching the top panel to the rear of the washer and slide the panel rearward and lift it off the washer.
Pull the dispenser drawer then push the locking tab and pull the dispenser drawer out completely. Remove the screw from the dispenser drawer opening including the screws attaching the top of the console to the cabinet then remove the console off the cabinet.
Remove the screws attaching the front panel to the cabinet then tilt the top of the panel and disconnect the wiring harness from the door switch assembly. Move the panel away to access and check the pump assembly.
Not finding what you are looking for?