20 Most Recent NetGear RangeMax NEXT WNR834B Wireless Router - Page 3 Questions & Answers

I don't think the Netgear WNR834B is capable of acting as a repeater but there is another solution. I would decide where I want to put the Netgear WNR834B for best coverage and then do the following. Go buy the Powerline Ethernet Adapters of your choice and put one at the main connection and plug a ethernet cable into a open switch port. Second go to where the repeater is to be located and plug the 2nd Powerline Ethernet Adapters in and connect to the Netgear WNR834B LAN port. Be sure to turn off DHCP on the Netgear WNR834B and assign a IP address that is not used. I normally use the highest address in the last octet so that I can remember for management. xxx.xxx.xxx.254. I hope this helps you.

Do you have a cordless phone in the area transmitting at 2.4megahertz?
If you do, that is what is breaking your connection. I found this out by accident.

If you go into your router there should be a listing on the left side that says port forwarding. It lists the ports most commonly used for gaming.

1. Check with the ISP ( internet service provider ) to see if you have proper connectivity to your router
2. Your satellite internet provider will assist you with your router settings
3. there may be an outage on the server if you are remote. Storms and transmitter issues may be the problem here.

Hi,

On Windows XP :
Click on start >> go to control panel >> double click on network connections >> right click on wireless network connection and click on properties >> click on wireless networks >> check the box that says ”use windows to configure my wireless network settings” and click OK >> right click on wireless network connection again and click on view available wireless networks. If you see your network name then click on it and click connect >> enter password if configured and click OK.
Note : If you don’t see wireless network tab under wireless network connection properties then follow below steps.
Click on start >> click on run >> type services.msc and click OK >> scroll the right side window down to wireless zero configuration >> double click on it >> start up type should be set to automatic and service status should be started (In case if it is different then change the settings) Then follow the above mentioned steps to look for wireless network tab and follow further.
On Windows Vista :
click on start >> go to control panel >> double click on network and sharing center >> onto left, click on connect to a network. If you see your network name then click on it and get connected.
[Note : If you don’t see any network name and wireless switch is turned on then follow the below mentioned steps]
Click on start >> click on run >> type services.msc and click OK >> scroll the right side window down to WLAN Auto configuration >> double click on it >> start up type should be set to automatic and service status should be started (In case if it is different then change the settings). Then try to connect to your network again.

a log on domain is the main network server that you want to connect to (more or less)

this would mainly appear on a LAN. (local area network)

for E.G

username: Ronald
Domain: Mcdonalds.co.uk
Regards
Soumajit

Switch off power to the modem, router and computer. Now switch on the modem first and let all lights on it to be stable.. Then switch on the router and let all lights on the router become stable. Once the lights on router are all stable, switch on the computer and then try to accerss sites.

1. log into the router and check the status page of the router.
2. check with the ISP to see if the connection to your premise is good.
3. logging into the router is: a.bring up browser page and type in 192.168.0.1 or the ,manufacturers ip for the router.
type this into the URL.

is there a reset button on it if so you can try to reset it and that should do the trick for you if you need more help just let me know

No solid power light = NO internet. Check and make sure router is plugged in. Try unplugging router for half a minute and plug it in again check and make sure the outlet works where you are plugging the router in and if still no power light you can contact Netgear support at 888-638-4327.

use netscan software to get ip of the router. And use the usename "admin" and no password.

Hi,


First you need to do wireless setting on router,steps to do wireless setting on router


1. Open a web browser (Internet Explorer, Mozilla Firefox or Safari).
2. Access the router, usually by typing 'http://192.168.0.1' or 'http://www.routerlogin.com' in the address bar.
3. Login to the router with the Username as "admin" and Password as "password" (please note that the Username and Password are case sensitive).
4. Click on Wireless Settings'(under Setup) from the left menu.
5. now click on ssid which be wireless-netgear..ch:11..security option select wpa/wsk ,under passphress type 9080706050
click on apply
now you need to do setting with Xbox360
link for doing setting on xbox
http://www.chasms.com/xbox/menu.htm
after click on above link please click on system/network setting
then follow instruction




Hope it can resolve issue
Thanks for using Fixya

Try restarting your router. If that doesn't work than check if you didn't accidentally hit the wireless button on your laptop as many people tend to do this and not realize it.

well if you forgot the username and password then reset the router for 20-30 secs pushing the reset button. powercycle the router for 10 secs. then open the router page>
-- http://192.168.1.1 or http://www.routerlogin.com or http://10.0.0.1
-- username and password is " admin" and "password"
-- Left side click on Setup Wizard
-- Apply basic settings
-- go to wireless settings
-- change ur wireless settings according to ur need
-- and apply all the settings.
and try to connect all the wireless computers

Make sure that your computer is able to go online directly through the modem.
If your computer is able to go online through the modem, that means the modem is working fine.
You will need to connect the computer to the router and the modem to the router.
open the set up page of the router and change the settings of the router according to the ISP.

Click Here for more information about the routers and network

No lights means either no AC power or a dead router.
If you have a multi-meter, you can test the voltage and amperage being emitted by the power-adapter brick.

Otherwise, it's better to spend $50 to buy a replacement, than it is to spend $50 on the time of a computer technician's "trouble-shooting" efforts.

enable security on router
1. Open a web browser (Internet Explorer, Mozilla Firefox or Safari).
2. Access the router, usually by typing 'http://192.168.0.1' or 'http://www.routerlogin.com' in the address bar.
3. Login to the router with the Username as "admin" and Password as "password" (please note that the Username and Password are case sensitive).
4. Click on Wireless Settings'(under Setup) from the left menu.
5. define your SSID(network name) under security option select WPA then typed your security in the passphresh then click on apply
6. than try to reconnect again again from your wireless device

regards
prakash

You need to "dial in" to your router. In your browser window, type 192.168.1.1 This will display a dialogue box asking for a username and password. [user name: admin] [ password: password] From here it is very easy to setup with lots of help displayed in the right hand column. TIP: do not change the login details as if you forget them, you cannot get into the router again. All machines on your network must have a unique IP but if you set to DHCP the router will provide the ip's automatically.

Log onto the router page by using the IP address in to the browser. To get that Open the Command prompt. To do that . Click start and in the run box type cmd. Or in the start search type cmd and right click and click on run as admin.

Then type ipconfig. Then the default gateway will denote the IP Adress of Router. Put that into the Browser and open the security settings and choose the encryption type and the password.