20 Most Recent Technics SL-BD22 Turntable Questions & Answers

0helpful
1answer

Cannot connect ground wire on SL BD26

Usually, on Technics turntables, the ground wire is attached to a ground lug on the receiver. If you need further help, I’m available over the phone at https://www.6ya.com/expert/david_29ad5d1dd86564b0
5/16/2016 12:26:23 AM • Technics SL-BD22... • Answered on May 16, 2016
0helpful
1answer

The volume on technics SL-BD22 turntable will not turn up and stays at one volume

Since the turntable itself doesn't have a volume control the problem is with the amp it is connected to. It should be connected to an amp with a dedicated phono socket. It's no use connecting it to a tape or aux or CD socket. These sockets do not have a built in pre-amp for the magnetic cartridge. If your amp doesn't have a dedicated phono socket then you can buy a Magnetic Cartridge Pre-amp that will plug into a tape socket etc on the amp and have the deck plugged into it. If plugged into a none dedicated socket though you can hear it, the volume will be very low compared to other sources. If you have got it plugged into a dedicated phono socket and the volume is still low, then the internal built pre-amp inside your amp for the deck has failed and will need to be repaired. The pre-amp failure will not effect any other functions of the amp.
2/24/2015 9:43:25 PM • Technics SL-BD22... • Answered on Feb 24, 2015
0helpful
1answer

Tehnics sl-bd22 noisy motor what to do?

If the bearing is worn to the point of a rattle and a small amount of silicone oil won't stop it, then it should be replaced or the motor replaced. These bearings are normally lifetime impregnated with lubricants and can sometimes dry out with use and somewhat seize up causing what may sound like a rattle. If the motor shaft has worn down enough at the bearing point, then a rebuild or replacement is in order.
12/26/2014 4:10:26 PM • Technics SL-BD22... • Answered on Dec 26, 2014
0helpful
1answer

Manual need one for Technics SL-BD22 Turntable. I

Technics SL BD22 Cheers john. Stylus City
11/29/2014 12:37:27 PM • Technics SL-BD22... • Answered on Nov 29, 2014
0helpful
2answers

The tone arm will not drop on our Technics sl-dd33 turntable.

Have you left the tone arm lift in the up position?
If not: At the end of a record the mechanism lifts the tone arm, returns it to the rest, lowers it and switches off the motor.
It the motor has stopped too early, the tone arm will remain raised.
You can try gently rotating the platter clockwise by hand. This may allow the return cycle to finish.
11/27/2014 1:51:07 AM • Technics SL-BD22... • Answered on Nov 27, 2014
0helpful
2answers

Tone arm wont lift up when returning, just scratches across the vinyl

If the problem is that the cueing control also does not lift the arm high enough, see the Adjustment section of the Owner's Manual: http://akdatabase.org/AKview/albums/userpics/10007/Technics%20SL-BD22%20Owners%20Manual.pdf
11/27/2014 1:45:54 AM • Technics SL-BD22... • Answered on Nov 27, 2014
0helpful
2answers

Tone arm on technics Sl-BD22 lifts before the end of an album

the anti-skate is set wrong, this stops the arm skatting on to the label in the middle of the record & destroying your stylus tip.
11/27/2014 1:39:45 AM • Technics SL-BD22... • Answered on Nov 27, 2014
0helpful
1answer

Stop button stuck one i press start. What should i do?

order the spring from the button and i would also replace the button , it ain't the money. Offcourse will a little bit oil around the button also will do the trickI agree that they are to loose , even with a knew unit. gr richard
9/29/2014 3:49:05 PM • Technics SL-BD22... • Answered on Sep 29, 2014
0helpful
1answer

Why tone arm stuck?

Depends on stuck , i think that i see often with you g dj's and then dirt is the problem and no maintenanance , if you cannot use your height adjustment any more, take the whole unit outand try very thin only , WITHOUT a lot of force to gebtle move it both ways , is very gentle stuff and the problem is often that they've pushed it the wrong side. Number two, the hair heater gently warm it 10 minutes(gloves) ans that will do the the trick and whem loose emediatialy clean and use good lubricant(not to thin), but when you wanna buy a table and the heightadjustment is jammed, it is a bad onr.....runnnnn
9/19/2014 3:22:48 PM • Technics SL-BD22... • Answered on Sep 19, 2014
0helpful
4answers

Drive Belt - Technics SLBD22 turntable

Try http://www.vintage-electronics.net/ttbelt.html
8/14/2014 9:48:30 PM • Technics SL-BD22... • Answered on Aug 14, 2014
0helpful
1answer

Need to know availability & price for spare stylii?

Best source is eBay. search for "Technics SL-BD22 stylus."
7/14/2014 2:03:44 PM • Technics SL-BD22... • Answered on Jul 14, 2014
0helpful
1answer

Crosley turntable on my record player is

Sorry Regina but it sounds to me like you need to ditch the Crosley & step up to a SL 1200 model.
3/15/2014 3:00:42 PM • Technics SL-BD22... • Answered on Mar 15, 2014
0answers
0answers
0helpful
1answer

Hi Stylus City. It's the T4P plug in connector with an EPC-P24S stylus that I'm looking for. Do you ship to the UK (N.Ireland)?

Hi, better late than never. Yes ship to UK and Ireland. Cheers john. Stylus City
12/4/2013 8:56:26 AM • Technics SL-BD22... • Answered on Dec 04, 2013
0helpful
2answers

Technics SL-DD33 Turntable

Well, it will play, it will just be very annoying to hear that humm. Unfortunately, you cannot get the wire plug from Technics, as it has been discontinued. So, the only other option is to take it to a service center, and have them 'hard-wire' a ground table to the unit. This entails opening it up and running a ground wire from the inside of the unit. Shouldn't cost you much, and should take about 30 min or so to complete. If you are quoted more the US$40, take it else where.

Any qualified electronics technician should be able to handle this. It's Audio Repair 101 - very easy stuff.

- OPTiC
DIGITAL ANALOG THERAPY
www.repairny.com
www.1200s.com

11/28/2013 12:05:40 AM • Technics SL-BD22... • Answered on Nov 28, 2013
0helpful
1answer

Needle doesn't make contact with album-can I

The weight at the end of the arm should be adjusted so that it applies pressure to the stylus. However sometimes the cueing leaver can get stuck or break, not allowing the stylus to come down on to the record. If the weight has numbers trying setting it to around 2 or 3. If it does come down, adjust it till that it neither rumbles or slips across the record. It's a question of trial and error doing this.
10/25/2013 12:28:28 AM • Technics SL-BD22... • Answered on Oct 25, 2013
Not finding what you are looking for?
Technics SL-BD22 Turntable Logo

135 questions posted

Ask a Question

Usually answered in minutes!

Top Technics Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5720 Answers

 Francisco Mauricio...
Francisco Mauricio...

Level 3 Expert

1551 Answers

Morne Olivier
Morne Olivier

Level 2 Expert

264 Answers

Are you a Technics Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Technics Audio Players & Recorders

  • Technics Audio Players & Recorders

Most Popular Question

needle doesnt make contact album

  • Audio Players & Recorders
Loading...