20 Most Recent GE Profile WPRE6100G Top Load Washer Questions & Answers

0helpful
2answers

GE WASHER LIGHTS FLASHING BUT NOT WORKING

It won't change because the cycle was incomplete and the safety control is preventing a restart. Until you get professional onsite service; unplug the washer; make certain all of the water is drained out, and disconnect the hoses. Have someone help you tilt the washer forward and lay on the front side. Pick it up again and reach into the tub area and spin the tube around, and kind-of move it side to side. Hook it back up, plug it into the power supply and reset the timer to start a short wash. Try to start and see if you get any action. If after all of that; nothing changed, the timer on the circuit board is stuck where you left off when the unbalanced load shut it down.
10/27/2021 4:01:27 AM • GE Profile... • Answered on Oct 27, 2021
0helpful
1answer

Washer drains but sometimes doesn't always spin.

Depending what unit u have most don't have belts now days the have direct drive couplers or single unit motors which act as motor and transmission all in one but more to ur point sounds like ur motor is getting week and needs replaced
12/20/2019 6:07:42 PM • GE Profile... • Answered on Dec 20, 2019
0helpful
2answers

What should l check to see why my washer won't drain

If spins, pump problem. If no spin thats problem. Motor reversing switch bad, possibly bad v belt on the bottom.
11/20/2019 5:55:38 AM • GE Profile... • Answered on Nov 20, 2019
0helpful
5answers

WH45X10060 - is this a joke?

do you need just the hub or do you also need the basket...I can sell you a hub.. let me know
3/19/2019 5:28:11 PM • GE Profile... • Answered on Mar 19, 2019
0helpful
2answers

Washer won't agitate or spin

Hello there and welcome to fixyathere are several things that you will need to check first ok please verrify the followingIt doesn't pump or spinIf it doesn't pump water out or spin, check to see if the motor is running, then proceed as follows:If the motor is running, your washer probably has a frozen pump pulley or a broken pump belt. To check the pulley, remove the pump from the washer and try to rotate the pulley manually. If it doesn't turn freely--if it's frozen or stiff--replace it. If the pump belt is broken or looks quite worn, replace it--but be sure to check the pump pulley before you change the belt.If the motor isn't running, the lid switch may be defective. If so, the washing machine can't spin and may not function at all. The switch is inside the washing machine main housing near the door frame. Often you have to raise or open the top or front of the washing machine to get to the switch. If it's defective, you need to replace it.It pumps, but doesn't spinIf your washer pumps out the water but doesn't spin, check these:The lid switch may be defective. If it is, the washing machine doesn't spin. The switch is inside the washing machine main housing near the door frame. Often you have to raise or open the top or front of the washing machine to get to the switch. If it's defective, you need to replace it.
12/30/2018 2:05:53 AM • GE Profile... • Answered on Dec 30, 2018
0answers
0helpful
1answer

GE Top Load Washer Loud Squealing Noise

Would check belt for tightness and it is also possible you have a dry bearing in pulley, motor etc.
1/16/2018 3:09:28 PM • GE Profile... • Answered on Jan 16, 2018
0helpful
1answer

If I run a load with the water at the "Large" or

check water solenoid or leakage from hoses or water level swith
12/18/2017 6:58:48 AM • GE Profile... • Answered on Dec 18, 2017
0answers
0helpful
1answer

Ge load size selector broken

You can buy this part, suggest you go online and purchase it. Contact this website: Appliance Parts Accessories Repair Help
5/19/2017 11:29:22 PM • GE Profile... • Answered on May 19, 2017
0helpful
1answer

New water pump isn't working. There were 3 wires

lucky that the machine is plastic or you would be getting a shock red wire is active , black wire is neutral and the green with yellow is ground all of the wires have a color code for a purpose and must all be connected correctly connect the pump correctly and the fault will dissapear
5/12/2017 11:54:41 PM • GE Profile... • Answered on May 12, 2017
0helpful
1answer

Load size dial won't set anymore, just spins freely

Most likely the knob is defective, order a new one.
4/25/2017 11:27:23 PM • GE Profile... • Answered on Apr 25, 2017
Not finding what you are looking for?
GE Profile WPRE6100G Top Load Washer Logo

579 questions posted

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Tim Whalen

Level 3 Expert

3076 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1482 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GE Washing Machines

  • GE Washing Machines

Most Popular Question

machine works but will not light up

  • Washing Machines
Loading...