Top 20 Technics SL-1200 Turntable Questions & Answers

Poor connection underside of wiring.

Technics SL-1200... | 182 views | 0 helpful votes

There is a capacator in you pre amplifier who is not working properly , replace this and it will work again. they use most this type 100uF/35V

Technics SL-1200... | 56 views | 0 helpful votes

Different cartridge output

Technics SL-1200... | 163 views | 0 helpful votes

almost often a wrong set table/arm weight and a dirty needle. . i gues the last. Cleanen record

Technics SL-1200... | 158 views | 0 helpful votes

It needs to be taken apart. The bottom needs to be removed. Not an easy job if you are not mechanically inclined. There are pots inside that need to be sprayed with contact cleaner. Pots are under the knobs that control the speed. They have holes on the sides of them. You can purchase cleaner at a radio shack or electronic parts store or online.
Potentiometer Wikipedia the free encyclopedia

Technics SL-1200... | 201 views | 0 helpful votes

can you be a bit more specific , do you want no music to play or else take a look on which type of music is in your pregerences coupled to which device and switch it.

Technics SL-1200... | 72 views | 0 helpful votes

50hz hum. Turn off most of your home equipment , turn only your table on, if it still hums it\'s your transformer and that\'s too bad for your wallet. And you also don\'t have those led lights which

is a fashion statement at the moment on your table, they are not quite good for causing distortion. And in your home are saving-lights. especially with dimmers and lcd plasma tv\'s a major cause of distortion. But a steady , low freq hum is your transformer and i have a stethoscope, not for that purpose:). Then you don\'t have to search. But they ain\'t cheap, the upgraded in 2009 ones.

gr richard

Technics SL-1200... | 111 views | 0 helpful votes

You can soon find out by leaving out the EQ. Best to check the cables that connect the units.

Technics SL-1200... | 52 views | 0 helpful votes

Hi, it needs to be earthed to your mixer or amp. Cheers john

Technics SL-1200... | 670 views | 0 helpful votes

Is it a belt drive turntable? If it is then either the belt is off or broken.

Technics SL-1200... | 38 views | 0 helpful votes

Hi, check to make sure the headshell is fitted properly to the tone arm and that the stylus is not damaged. Cheers john. Styluscity

Technics SL-1200... | 502 views | 0 helpful votes

The closest font I found is "Arial". I based it on the numerals used.
I do belive the fonts for the word "Technics" is different

Technics SL-1200... | 1,119 views | 0 helpful votes

Could be a couple of things. Could be the alignment, weighting, tracking or all of those causing this. It could be the gain structure on your mixer is not set and is too high. Maybe that the output of the cartridge is to high for standard mm inputs

Technics SL-1200... | 159 views | 0 helpful votes

Hi, remove it and give the contacts a good clean. If that doesn't work it will need replacing. John

Technics SL-1200... | 400 views | 0 helpful votes

Use the slide on the pitch control to move forward or backward until the dots stay steady. If it is a little old the quartz control won't work as well.

Technics SL-1200... | 145 views | 0 helpful votes

Generally the cause is one of 3 things. 1 Damage to the stylus or dirt. 2 Lack of pressure to the stylus. 3 Anti-skate control set to low.
First check the stylus you should feel it sticking in you finger a bit. 2 Has the weight on the end of the arm become lose? Adjust for the correct tracking weight of the cartridge. 3 Check the manual for what the anti-skate control should be set to.

Technics SL-1200... | 1,013 views | 0 helpful votes

you changed it back and it doesnt work? theres a little switch that is 120 or 240 or something like that US is 120 uk is like 140

Technics SL-1200... | 104 views | 0 helpful votes

Turntable Drive Belt

The chances are the rubber drive belt has either broken or stretched so that it has fallen off the drive pulleys.

You will need to gain access to the underside of the turntable to replace it.

With most turntables the process will be to secure the tone arm (a rubber band will do the trick) before turning the whole thing upside down and unscrewing the base.

Replacement drive belts are easily available on the internet. Search by make and model number of your turntable

Technics SL-1200... | 231 views | 1 helpful votes

First off, Congratulations on such a excellent deal! That's a $500.00 turntable. I know I own a pair and I've been a DJ for 18 years.

Second, the Technics 1200 does not have an auto return. You have to pick up the needle and bring it back manually.

Technics SL-1200... | 224 views | 1 helpful votes

wik-wikkit-wow-chika-scribble-scrab. word.

Technics SL-1200... | 28 views | 0 helpful votes

Not finding what you are looking for?
Technics SL-1200 Turntable Logo

Popular Tags

116 questions posted

Ask a Question

Usually answered in minutes!

Top Technics Audio Players & Recorders Experts


Level 3 Expert

5700 Answers

The Knight
The Knight

Level 3 Expert

76407 Answers


Level 3 Expert

85239 Answers

Are you a Technics Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Technics Audio Players & Recorders

  • Technics Audio Players & Recorders

Most Popular Question

just purchases technics 1200 turntable

  • Audio Players & Recorders