20 Most Recent
Sansui DTV2760 27" TV - Page 4 Questions & Answers
Hi, I have had my
Take your remote press menu and scroll down to audio, check the audio settings carefully, if you find speakers off turn it back on that will restore the sound, failing that! check to see if the mute is on if it is turn it off to get the sound back. If none of these work I suggest a tv technician to remedy the situation.
I have a sansui tv set with a power problem .
Hello
W11NB80 is an N-channel 800V-0.65ohm - 11A - rated Metal Oxide Semiconductor Field Effect Transistor [MOSFET]. You can use the folowing substitutions for it
[ 11NM-80, 12NK-80 & 10NC-802]. All of these are its equalent substitutions.
Before replacing the mosfet, check the entire power supply secion for any short circuit, or zener diodes faults. If any of the zener diodes are fused, it will run out the MOSET you sumstitue again. Check it keenly. Unsolder one end of each component, lifit it up a liile from the circuit board and check. Especially zener diodes must not show any leak in 100Kohms range. It is best to replace them all I suggests.
I don't know about its availability in Keniya, yet you try to get it from any electronic spare part shops. f feels any difficulty in getting the same contact [E-Bay] site, they will reach you the exact component at your doorstep. Ok.
Tv comes on out of horiz sync. H.V. within normal
Hi,
TV have boards that control vertical and horizontal output to their respective areas. They are connected to the screen by ribbon cables. If one of these boards fails all together, has a failed chip, a bad connection, or a bad ground somewhere it will result in a black line in the area of that board. A bad ribbon cable connection on the bottom will result in a vertical black bar though the screen. Many times resetting the connection will fix it, if the ribbon cable has been nicked there could be a severed connection. They an sometimes be fixed, but it is a pain. An yes I have done it, but the bar is gone. The same will happen if the chip that outputs to that area opens. The connectors are the first place to look paying close attention to the cable, they are extremely delicate so great care must be taken
Hope this help in solving......
Where do the tone control of your amplifier its
Hello
What do you want to do with your Sansui DTV2760. Please clarify your post. I can't understand anything for your post. Do you want your Amp to be connected to the TV, or do you want to connect the TV to your Amp. Clarify please.
My television continues to display the phrase
Go to Menu - then channel - then memory channel - let the tv reconfigure the channels. You might need to unplug tv (the light to tv might still be on - press the on button to release the juice). Then plug tv back in. I did this and it worked.
Sansui tv repair.pur.dt 14.02.2009.already
Hello
If you go with a dead TV for exchange, you get nothig for that set. Make it work at anyway and go for an exchange. It is best for you to go for a fresh shopping, without your TV. Now is X'mas season, and so many companies will offer special discounts, and special gifts. If you go for an exchange shopping, they won't give you anything, and they will get your TV absolutely free.
Think about it once more and do the needy. OK.
When I turn the TV
must make a good maintenance has to take the card out and resolder and laverla with thinner or gasoline can be cold welding are not making good contact
I have a sansui k2k121
You can enter the "Service Mode" by turning the "On" then holding the Vol Down (-) on the set and the 9 on the remote for more than 2 seconds. This enters the set into service mode. Make sure the volume is all the way down first. Be Warned, messing with these adjustments can cause irreparable damage to the set. Before you make ANY changes I suggest you go through the list and write down each and every Name and Value in the menu. That way you have something to fall back on when you change something and want to restore it's original value. To exit service mode and save your changes, Power the off with the power button on the set.
The tv is off it
If you were to log on to the
manufacturer's web site, I think you will be pleasantly surprised as
usually one is able to download, by model number, Customer
Instruction Manuals, list
of Dealers,
and
Installation Instructions
as required.
Just Google the manufacturer's name and
follow the links. Make certain you are directed to the manufacturer's
web site as some search engines direct you to other sites and they
charge for the information that is normally free of charge.
I hope this helps.
How do i set a universal remote to a sansui tv
Hi,
Firstly, you need to let me know the brand and EXACT model number of your universal remote control. This will usually be at the bottom of the remote on the keypad side, on a sticker on the back or sometimes inside the battery compartment.
Please post back with the above information and I will provide codes and programming instructions for your remote. Please note, there is no guarantee that your remote will work with your TV - especially if the remote is older than the TV.
Nobody can help you unless you specify the brand and model number!
Thanks.
Tv comes on has good picture and then just shuts
In these cases you might be able to see a
picture by shining a bright light right next to the screen front. Do not put the light there for very long or you will end up
with a permanent bright spot burt onto the screen. I have discovered that applying light pressure with a 3/8" thick rubber or
plastic shim corrects a panel inverter/driver board/card solder problem with many flat panel TVs. (Removing
the back is required, try light pressure against the board while wearing rubber gloves and tv is then powered on.)
Not finding what you are looking for?