Connex 4400 320-Channels Base CB Radio - Answered Questions & Fixed issues


should be the standard 3 pin plug for any radio .

Connex 4400... | Answered on Sep 03, 2016 | 116 views


unless you have the equipment to do this.. please take to a radio store. have them do it.. its free. or they shouldn't charge to do that service.. unless it needs a major factory alignment.
also they shouldn't take out or clip anything in the process if they do find you another place LOL..

Connex 4400... | Answered on Feb 02, 2016 | 298 views


  • Yes you can. This is actually a service manual but it covers the basics found in the users manual in the first part of the first link. Also with a service manual you can dissect the radio to perform repairs.


  • Part 2 -
http://www.cbtricks.com/radios/connex/cx_4400_cx4400hp/graphics/connex_cx4400_cx4400hp_sm_pg16_pg33.pdf
Regards, Tony

Connex 4400... | Answered on Apr 30, 2011 | 441 views


1-SHIELD
2-AUDIO
3-TX
4-RX
YELLOW-N/C
MAYBE THIS WILL HELP

Connex 4400... | Answered on Oct 13, 2009 | 137 views


Check for proper shielding,ground, turn mic gain down, move mike farther away from radio, turn off other accessories nearby-ie.-am/fm radio

Connex 4400... | Answered on Mar 24, 2009 | 361 views


it wasn't the 4558 chip... am still hunting...

Connex 4400... | Answered on Jun 06, 2008 | 195 views


if your swr is higher on 1 then on 40 then your antenna is electrically short and you have to lenghten the antenna.If it is higher on 40 then on 1 then it is long and you have to shorten it. If you have to make it longer then you may have to add a quick disconnect or a coiled spring to make it longer. To make it shorter all you have to do is trim a 1/4 in at a time off the antenna whip but you must keep checking the match until it gets down below 1.5 .

Connex Radio... | Answered on Oct 03, 2018 | 56 views


Have you tried keying it without the coax attached ? Take the mic apart and give it a squirt of electrical parts cleaner .Try using a different mic also.

Connex Radio... | Answered on Oct 03, 2018 | 250 views


If you disable any part of the radio that does not pertain to CB then you could actually do damage to the radio. the best thing to do is leave it on the CB band and don't touch it.

Connex Radio... | Answered on Oct 03, 2018 | 367 views


the radio is searching for a strong incoming signal and until it gets one it will search for one. Try turning off the scan button .

Connex Radio... | Answered on Oct 03, 2018 | 83 views


Probably inside the unit

Connex Radio... | Answered on Aug 30, 2018 | 97 views


many trucks have a ground wire in the harness as the cabins are fibre glass or not grounded around the cabin mounts If the radio grounds out through the frame , then there would be no ground for the radio or the aerial wire
to fit this particular may require such a wire in the harness for the radio which it probably doesn't have
As you have been alerted to a problem, it would be advisable to talk with professional radio fitters who work on trucks to get the correct advice before starting on the job
it could save a lot of frustration

Connex Radio... | Answered on Nov 23, 2017 | 33 views


Sorry we do not sell parts nor have the ability to locate them for you.

Connex Radio... | Answered on Jun 08, 2017 | 33 views


If you ground the audio wire, you will have no noise or mic function at all. The mic hot wire and the shield should be enough to avoid hum.

Connex Radio... | Answered on Jan 22, 2017 | 100 views


contact connex and they will give you a repair number and let you know where to send it.

Connex Radio... | Answered on Dec 04, 2016 | 194 views


Fixya is not a buying service.

Connex Radio... | Answered on Nov 03, 2016 | 109 views


Is the CB getting its power from the amp(?) By amp I will assume you are talking about a signal amplifier..

Connex Radio... | Answered on Oct 05, 2016 | 125 views


people think that if they peak and tune a radio it will work better. First, if its brand new from the factory you shouldn't have to,all you should have to do is lower the dead key raise the modulation and you are good to go . The proper way to do this is with a spectrom analyzer . Do you have one? Cheap on ebay ,may 4000-5000 dollars but if you get one and set that radio perfect you should hear anyone complain that you are interfering with their radio.

Connex Radio... | Answered on Sep 13, 2016 | 248 views

Not finding what you are looking for?
Connex 4400 320-Channels Base CB Radio Logo

Popular Tags

9 questions posted

Ask a Question

Usually answered in minutes!

Top Connex Radio Communications Experts

Brad Brown

Level 3 Expert

18401 Answers

Tony Raia

Level 2 Expert

260 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Connex Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...