Samsung Weather Resistant Security Camera SSC-12C - Answered Questions & Fixed issues

I salvaged an SOD14C and found this out by playing around with it. the 6 pin RJ11 is wired as follows, holding the cable, connector up, cable hanging down with the pins facing you the pins count from left to right. Pin 1 is green it is the Microphone + Pin 2 is red it is the +12 Volts DC Pin 3 is yellow it is the Speaker + Pin 4 is the bare copper shield it is the common (-12 Volts DC, Microphone -, and Video -) Pin 5 is whitish clear it is the Video + Pin 6 is black it is the Speaker - Hope this helps!

if it is an IP cam then yes you will need a router to connect it to you NVR. there is normally an option to connect coaxle (RG59) cable on the back of an IP cam but this is not recomended as the quility may be poor.

I can't seem to find a pin out, it you post what wires are there I can help you figure out the most likely pinout without damage to the device--Good Luck.

Unfortunately, the devices aren't listed as the "set" - can you reply with the exact model number from the main unit?If i cannot obtain the schematics after hearing from you... I will contact Customer Service to initiate a refund or switch to another expert.Thanks!

You can download the manual at
http://downloadcenter.samsung.com/content/UM/200604/20060413114602671_SSC-12.pdf

http://downloadcenter.samsung.com/content/UM/200604/20060413114602671_SSC-12.pdf

That will happen with pretty much any camera on the planet.

I have a suggestion... use a slightly tinted glass on the enclosures, or get the 2% (or whichever one you think will be enough) tint film used on car windows, and put a square of it on the enclosure glass.

Hi there, depend on the model of your cameras, normally if there are samsung it should say the model # ( ssc-12c,soc-c120 and so on) What look like CAT-5 are normally RJ-11 very similar to a phone connector. If your cameras are one those mentioned above you will need a monitor that support that type of connection like the ssc12m or ssc-17webm if there are black and white or the SMT-190M if there are color cameras. or a DVR with similar connection type like the SHR-1041.
Thank You,
nationalprosecurity.com

green wire : 12v dc

clear wire : video ( + )

wire around clear wire : video and 12 vlt ground ( - )

you don't used the rest of wires . rest are audio .

rj11e pin lay out with turned over. brass pin facing you.release
pin to the bottom. 1 left to right to 6.
1 2 3 4 5 6
' ' ' ' ' '
bk---red--green--yellow--clear (bare ground)--

that is it.

You can download the manual from
http://www.samsung.com/us/support/supportDownloadCenter.do?prd_ia_cd=N0000000&prd_mdl_cd=SMO-152QN%2FXAA&prd_mdl_name=SMO-152QN

Well the conditions exceed the camera's ability. I suggest that you call Samsung and see if they have the solution. A filter lense may help during the day, but hinder after dark...

It's a quad. It records all 4 cameras at the same time. You can display 1 cam at a time. If you play it back, you have to hit the buttong that displays the corresponding camera you want to review.

I have the same problem and I found out that a resistor went bad and then a capicator went bad.you must have them check and replcaced

red and ground are most likely for 12 volt as you indicated.
white should be your video out which will work with the ground that comes out of the camera.you can connect these wires to a cable that will be termintated with the proper connector at your dvr

i recommend pelco day night dome camera they are cheap and the resolution is great. they are originally bnc type connector which usually take rg59 or rg6 coax cable but if you have like cat5 or some other kind of stranded wire you can by a balum adaptor that takes stranded wire but has a bnc female end. now with your monitor they make a cheap device called a multiplexer it takes bnc connectors and to hook up to your monitor you can use regular adio video cables like for your vcr. the multiplexer also lets you scan thru your cameras one at a time or have all three up or it can scan thru by itself like every five minuets.

is this poe cam? cable footage over 300 ft needs cat5 extender if fiber check media converter to see if single or multimode also check media converter for tx/rx or using cat5 b crossover cable connect directly to laptop type in ip in command bar enter

3-pair version of (red/green, black/yellow, white/blue). But the first two pairs are not twisted
So it becomes green/red, yellow/black, & white-black/blue. G1/ R2 /3Y /4B /5*Blk/6Blue (this is what you physically see on the other RJ11 connections since this is a data connection and not a phone connection it should be a straight-through instead of cross-over connection.
These RJ 11 PINOUT assignments may be incorrect because they apply to a color camera instead of B/W

1 SPEAKER (+)
2 VIDEO_OUT
3 GND
4 SPEAKER (-)
5 AUDIO_OUT/ALARM_OUT
6 12V DC
Back of Camera
Clip up, contacts down
123456
RJ11-e starts off like a RJ45 Stranded Patch Cable.
The color code used in stranded patch cables is different from solid-conductor cables. For NorTel Digital Patch Cable (DPC), the coding is; Pair 1: Green & RedPair 2: Yellow & BlackPair 3: Blue & *Orange White\Black
*In Pair 3 the color coding is Blue & Black instead of Blue & Orange and the pair is twisted so that the Blue wire is the 6th pin instead of the 5th pin.

im trying to get the wiring dirgam for a ssc-12c camera

Try ebay. It will save a alot of trouble