To add a 2-channel amplifier to your Denon AVR 2307ci receiver, you can follow these general steps:
1. Determine the amplifier connection type: Check the specifications of your 2-channel amplifier and identify the available input and output options. Common connection types include RCA (analog) and speaker wire (for binding posts or terminals).
2. Identify the pre-out connections on your Denon AVR: Locate the pre-out connections on the back of your Denon AVR 2307ci receiver. These are typically labeled as "Pre Out" or "Preamp Out" and may be color-coded. You will need to find the pre-out connections for the front left and right channels.
3. Connect the RCA cables: If your amplifier has RCA inputs, use RCA cables to connect the pre-out connections of the Denon AVR to the corresponding inputs on the amplifier. Connect the left channel pre-out on the Denon to the left channel input on the amplifier, and do the same for the right channel.
4. Connect the speaker wires: If your amplifier uses speaker wire connections, connect the front left and right speaker outputs of the Denon AVR to the corresponding inputs on the amplifier using speaker wire. Make sure to observe the proper polarity (positive and negative) when connecting the wires.
5. Configure the Denon AVR settings: Access the setup menu of the Denon AVR by using the remote control or the front panel display. Navigate to the audio settings or speaker configuration section. Look for an option to enable "Preamp Mode" or "Preamp Outputs." Enable this option to ensure that the front left and right channels are redirected to the pre-out connections.
6. Set the amplifier to the correct input: If your amplifier has multiple inputs, select the input that corresponds to the connection from the Denon AVR.
7. Adjust volume and settings: After completing the connections, you may need to adjust the volume levels on both the Denon AVR and the amplifier. Use the Denon AVR as the primary volume control and adjust the amplifier's volume accordingly.
It's important to consult the user manuals for both your Denon AVR 2307ci and the 2-channel amplifier to ensure proper setup and compatibility. If you're uncertain about any specific steps or settings, it's advisable to consult the manuals or reach out to Denon customer support for assistance.
This video MIGHT help a little
if you want to set your playback speed exactly right, you need a test tape with a test tone on it (3khz for example). now you hook a frequency counter to your tapedecks output and set the speed accordingly.
It sounds like there might be an issue with the HDMI handshake between the Denon AVR-2807 and the Hisense 4K 65A6H. Here are a few things you can try:
Check the HDMI settings on both the Denon AVR-2807 and the Hisense 4K 65A6H to make sure they are compatible with each other. Some HDMI settings such as HDCP, HDMI Control, and CEC can cause issues when they are not set correctly.
Try using a different HDMI cable. It's possible that the cable you are currently using is not compatible with the Hisense 4K 65A6H.
Update the firmware on the Denon AVR-2807. Sometimes firmware updates can fix compatibility issues with newer devices.
Try connecting the Hisense 4K 65A6H directly to the cable box and see if the sound works. If it does, then the issue is most likely with the Denon AVR-2807.
If all else fails, you may need to consider upgrading your Denon AVR-2807 to a newer model that is compatible with the Hisense 4K 65A6H.
You can try a power reset first. Disconnect the mains power plug for 5 minutes, then press and hold the power button as you plug it back in, continue to hold for 12 seconds.
If that doesn't fix it, take it to an audio repairer.
..
Question edited for clarity and 'AVE' to 'AVR'..
Yes of course no problem. The speakers are just that, a speaker, the processing is done by the Denon box not the speaker. You can use any speaker with an impedence of 6 to 16 ohms.
https://www.hifiengine.com/manual_library/denon/avr-3300.shtml
..
If you have verified that the Denon AVR 3310CI is properly configured and connected to the speakers but are still unable to hear anything, you can try the following troubleshooting procedures:
Examine the HDMI cables: Check to see that the HDMI cables are securely connected to the HDMI output port on your source device and the HDMI input ports on the receiver's back. To see if that resolves the issue, try substituting new HDMI cables.
The microprocessor must be reset: The functions of the Denon AVR 3310CI are controlled by a microprocessor. Try powering the receiver back on while simultaneously holding down the "Power" and "Speaker A" buttons to reset the microprocessor.
Check the settings for the sound: Check that the sound settings on the receiver are set up correctly. To ensure that the settings are optimized for your particular setup, check the model's manual.
Aktualize the firmware: Check to see if the Denon AVR 3310CI's firmware can be updated. For additional information on how to update the firmware, you can visit the Denon website or get in touch with their customer support.
Use a different source to test: To determine whether the issue is with the receiver or the original source device, test it with a different source device.
The code for the Denon S760H for a Dish Network remote is 0476. You can usually find the code listed in the manual for your remote, or you can search for the code online by typing in the model number of your receiver.
Okay! all ceiling mounted speakers. I don't know about 4 pair of speakers.Here is the load down: First pair of ceiling speakers would be left and right front from speaker A or Main output behind your receiver. Second ONE,but a pair would be connect to the center channel output as your center speaker. Another pair would be connect to the surround sound left and right(NOT surround BACK left/right.) Now,you have 5 channel setup at this point,you still need to purchase a power subwoofer to the SUB PRE-OUTPUT behind your Denon receiver.
For Zone two,you would need to connect your other pair of speakers to surround BACK left and right output. Go to your Denon MENU button,depending on which model you have,some of them will have an on-screen display feature(you would need to have a composite video cable connect from the video output behind your receiver to the TV video input in order to use the on screen menu.)If not,you would have to it view on the front panel of the A/V receiver. You need to read the detail on how to setup the video and audio as well as distance and DB for the receiver through the menu button. I will be frank with you,if you are an amateur,Denon is NOT easy to be setup on the first time. solutiondoct
The clue I think is the fact the problem gets worse after being switched off. One cause could be leaking capacitors, the big ones in the the power supply. They hold a charge, but if they leak the charge is lost and they do that when the power is off. The only other I can think of is a voltage regulator. But I think that would blow a fuse. So I would get your guy to replace the caps.
