Jack Lalanne Power Juicer (Stainless Steel) - Page 4 - Answered Questions & Fixed issues
It will not turn on, i tried the reset button
Check the plug end of the power cord--if the cord is pulled instead of the plug, it can cause breakage of the wires inside the cord. Try pulling the plug from the cord--if the insulation seems to stretch-out, shorten the cord a little(an inch or so) and install a new replacement plug. If cord seems ok, then an internal inspection of the motor area is the next option.
7/12/2009 3:14:08 AM •
Jack Lalanne...
•
Answered
on Jul 12, 2009
•
203 views
No power. Thanx for help.
Cha-Ching. Finally. I could not sit still until tomorrow to call customer service. For a moment I thought my power juicer motor was shot. :( I was a bit sad. I patiently took apart all of the screw to realized that I only need to unscrew 3 screws on the bottom to get to the motor. Once the bottom part is open I see that one of the cables are loose and just reattached it. It is very simple wiring inside. There is only 3 cable and 3 attachment spot inside...so pretty simple. :) Happy again and Juicing :)
5/4/2009 7:54:00 AM •
Jack Lalanne...
•
Answered
on May 04, 2009
•
237 views
How do I disemble the juicer
again, after having the same problem, i watched the video at link given here earlier. i used two ballpoint pens and gently turned the blade counterclockwise and it worked!
4/22/2009 9:17:18 PM •
Jack Lalanne...
•
Answered
on Apr 22, 2009
•
287 views
Juicer will not run
Make sure the stainless bar running across the top is snug on the left
and right groove. It has a shut off switch when not installed properly.
4/4/2009 8:47:09 PM •
Jack Lalanne...
•
Answered
on Apr 04, 2009
•
324 views
STRIPPING DOWN THE JUICER FOR CLEANING
Yes. There should be an orange handle-looking accessory with to small metal rods sticking out that is made to clik into the wire mesh screen and unlock it be twisting the screen mechanism slightly so you can unscrew it out.
See the enclose photos of the tool.
Hope this helps...
-enov8
3/7/2009 7:14:59 AM •
Jack Lalanne...
•
Answered
on Mar 07, 2009
•
291 views
Cant grt it apart to clean
Take off the top part of the juicer that has the chute. You will see the blade and basket. The blade appears to be attached to the basket with three small screws but is actually screwed onto the basket by a large screw that protrudes out of the basket underneath the blade. So the trick is to unscrew the blade, turning it to the left by using maybe a small screwdriver that you will have to put into one of the two small holes that are on the blade surface and pushing the blade to the left. This should loosen the blade and then you can just unscrew the blade off the basket. Once you get that blade off, the rest of the juicer comes apart. The newer models come with a little tool with a couple of arms that go down into those holes and loosen the top. Good luck.
8/3/2010 5:50:01 AM •
Jack Lalanne...
•
Answered
on Aug 03, 2010
•
1,036 views
Power juicer not working
Hi my name is patricia you probably have to have the handle bars on or up so it can be tight and then the motor will run.
12/14/2008 11:03:16 AM •
Jack Lalanne...
•
Answered
on Dec 14, 2008
•
552 views
Can't get filter out?
Well this is September ,so i just got one to,so i dont know if you solved your problem since then,but you never take the screws out the blade to take the blade out you keep screws in and take the vise gripe the black vise grip and put it in the blade while still in the processer and turn it left keep turning it and the whole thing will come off and so you will be able to clean the filter .
11/14/2008 7:19:38 PM •
Jack Lalanne...
•
Answered
on Nov 14, 2008
•
558 views
Jack LaLanne Power Juicer
Hi smer67 - This is what it says on the official site about spare parts: See the back inside cover of the instruction manual for the spare parts order form or call: 1-973-287-5150
(MON-FRI 9AM to 7PM EST & SAT 9AM - 5PM EST). If this answers your question PLEASE rate this as fixed. If you need more help just add a comment and I'll be happy to assist you further. Thanks.
Jeff
8/4/2012 6:10:01 PM •
Jack Lalanne...
•
Answered
on Aug 04, 2012
•
586 views
Taking apart Jack Lalne power juicer to clean.
There are two holes on the surface of the blade. When the juicer was bought, it came with a half moon shaped orange tool that has two posts that fit into these two holes.
By inserting the tool into these holes you can unscrew the blade from the machine as long as you hold the outer screen while doing so.
Once this is done, you simply lift the other pieces off.
If you can't find your orange two prong tool, i would suggest using a screw driver or two that fit into the hole(or two)..... hold the orange screen and turn the blade counter-clockwise..
Hope this helps
Smitty
2/21/2009 9:22:28 PM •
Jack Lalanne...
•
Answered
on Feb 21, 2009
•
1,698 views
Pusher won't come out
Hi,my name is patricia ,and i found a solution,first the black button .the black vise grip put it in the blade while the blade is still in turn the black vise grip to the left while still in the blade keep turning to the left and the blade will come off of the black button.the black button do not come off or up.When you put food in but smaller pieces in and have all your pieces near you so you can continue to drop in in the processer while running it and can slowly put the long tube in to keep food from splashing do it slowly .hope that help
9/9/2008 4:48:58 PM •
Jack Lalanne...
•
Answered
on Sep 09, 2008
•
550 views
Not finding what you are looking for?