20 Most Recent
Amana 24 in. ADW862EAS Dishwasher - Page 7 Questions & Answers
Noise in washer when running
usually this indicates the drum bearing needs to be replaced. The sound it makes depends on the age and the make but you'll know one way or another as it is rumblig sound.
12/15/2009 6:43:44 PM •
Amana...
•
Answered
on Dec 15, 2009
My amana dishwasher is not issuing any water
HI. this is a water inlet valve issue. i recommend testing this device. it may be faulty.
To access the inlet valve remove the lower panel located beneath the door. The panel is usually held in place with two screws either above or below the panel. It may be necessary to first open the door to the dishwasher to reach the screws over the panel, then close the door to remove the panel. The water inlet valve can be identified by the water hoses connected to it. One hose will lead from the valve to the pump/motor assembly in the center of the dishwasher. Check that the hoses are securely connected to the valve and that there are no kinks in the hoses which could restrict water flow. There are two wires (four, if it has two solenoids) connected to the water inlet valve. Label the wires and connections so that you can properly reconnect them later. The wires are connected with slip on connectors. Firmly pull the connectors off of the terminals (do not pull on the wire itself). You may need to use a pair of needle-nose pliers to remove the connectors. Inspect the connectors and the terminals for corrosion. If either is corroded they should be cleaned or replaced. Use a continuity tester or multimeter to test for continuity. Set the multimeter to the ohms setting X1. Touch one probe to each terminal. A reading of infinity indicates a bad solenoid that must be replaced. Different brands and models will have various measurements, but the valve should show some resistance if it is functioning properly. If your valve has two solenoids, test the second one in the same way as the first. If the solenoid is working properly, but water leaks through the valve even when the dishwasher is off, then the valve itself is the problem. Debris may be preventing the valve from closing. If the valve cannot be cleaned, it will have to be replaced. The valve can also fail mechanically. So even if it passes the electrical test, it may still require replacement. If you have ruled out all other possibilities, go ahead and replace the valve.
**(((If the inlet proves to be functional with no leakage, this will lead to the control. its has failed in this case. replace it asap)))
12/5/2009 11:17:31 PM •
Amana...
•
Answered
on Dec 05, 2009
Amana dishwasher, model adb2200aws, ser
the person or persons that crimped on your spade push on) terminal ends, either cut thru most of the wire when stripping it for the terminal connector, leaving only very few wires, and /c they cannot carry the current, they simply vaporize leaving a terminal securely attached to plastic insulation - but no wire to carry the current.or he/she/it failed to properly prepare the wire end to expose enough wire, and crimped onto the insulation, leaving the wire hanging.
Pull the plug
Grab each of the power-related wire ends in turn and with your fingers, try to pull the crimped-on end off. Do not pull hard, although IF it was correctly stripped and crimped at the factory, you would not be able to. I am sure you will find one that feels very limp.. thats the culprit. Nip over to Home Depot or ACE and buy a Wire Termination kit ($10-20.00) which will contain all sizes andtypes you may need + a Cut/Strip and crimp tool.
It was either a MON or FRI job. Too hungover from the weekend... or too jumpy to go home.
11/13/2009 10:14:03 PM •
Amana...
•
Answered
on Nov 13, 2009
Amana Sofsound II Dishwasher, heated
push the button for a different option: it's like a radio button in Hypercard: one must be chosen, and choosing one will "unselect" the others.
8/14/2009 2:30:57 AM •
Amana...
•
Answered
on Aug 14, 2009
The water does not drain out. Water in tub bottom
hi
Most dishwashers discharge used water through a pipe or a hose connected to the drain or garbage disposer under the kitchen sink. If the drain line is made of flexible hosing, it may have cracked from prolonged exposure to hot water. Examine the hose; if it's damaged, replace it. If the hose is leaking at its connections with the disposer or dishwasher, tighten the fittings or clamps at the connections, or replace the clamps. Also check for water leaks around inlet valves, drain valves, and anywhere you see flexible hoses and hose connections. Leaks at clamps can be stopped by tightening or replacing the clamps. Leaks in hoses can be eliminated by replacing the hoses.
9/13/2008 1:15:19 PM •
Amana...
•
Answered
on Sep 13, 2008
The door handle on my
The door latch and handle assembly needs to be replaced. If you have a handy person order the part and replace it....otherwise you may need a service tech
7/28/2008 9:52:21 PM •
Amana...
•
Answered
on Jul 28, 2008
AMANA ADB1500AWQ Control buttons not
unplug the power cable from wall socket.check the voltage from the household receptacle to the dishwasher, volt meter.It might be your neutral line is bad,or the console is bad
7/24/2008 12:33:45 AM •
Amana...
•
Answered
on Jul 24, 2008
Tub water dirty
Removed 2 separate filters that were heavily clogged and cleaned them.
7/17/2008 1:39:56 PM •
Amana...
•
Answered
on Jul 17, 2008
Does not seem to spray
If you have good water to the unit with very little inside then you need to check the fill valve on the unit itself. They get plugged up fairly easy. They are easy to replace also with just the house line, one fill hose, two wires, and a couple screws.
5/16/2008 3:02:49 AM •
Amana...
•
Answered
on May 16, 2008
DIO3T131FEUK Integrated dishwasher has power but won't switch on
Check Power Supply:
First, ensure that the dishwasher is properly plugged into an outlet. Sometimes vibrations or nearby appliances can cause it to come unplugged.
If it's plugged in, test the outlet by connecting a small appliance (like a toaster or blender) to see if it turns on. If it does, move on to the next step.
Check Circuit Breaker:
Verify if a circuit breaker has tripped. Go to your circuit breaker box and look for any tripped breakers.
If you find one, flip it to the "off" position and then back to the "on" position.
Test the dishwasher again to see if it powers on.
Child Lock or Delayed Start:
Some dishwashers have a child-lock feature that prevents accidental starts or changes to the wash cycle.
Check your owner's manual for instructions on disabling the child lock or delayed-start features.
Ensure that the dishwasher door is securely latched.
Reset the Dishwasher:
If the dishwasher has power but won't start, it might be stuck between cycles.
Allow any drain cycle to run (if applicable), wait for 60 to 90 seconds, and then press the start button once.
Unplug the dishwasher for a minute or two, then plug it back in. This can help reset the machine.
Refer to the owner's manual for any specific reset procedures.
If none of these steps resolve the issue, consider reaching out to professional repair services or the manufacturer for further assistance.
4/21/2024 2:44:15 PM •
Dishwashers
•
Answered
3 days ago
Karcher Puzzi 100 Spray pressure low
troubleshoot the issue:
Spray Nozzle Blockage: Ensure that the spray nozzle is clear and not blocked. Sometimes debris or buildup can obstruct the nozzle, affecting the spray performance.
Pump Coil and Circuit Board: The pump coil could be damaged or broken. If it's faulty, the pump won't spray at all. You can check continuity through the coil and verify that the switch is supplying power to the circuit board and, in turn, to the pump. Dry solder joints or a failed smoothing capacitor on the circuit board can also cause issues. Pumps are relatively simple solenoid plunger types, and replacements are available for around £40-£50. If you're not comfortable testing at mains voltages, seek professional assistance.
Calcium Buildup and Blockages: Some pumps can be dismantled, allowing you to remove any calcium buildup or blockages. Gently tapping or shaking the pump might get it going. Recirculating a descaler can also help clear buildup without disassembly.
Pump Replacement: If the pump is indeed faulty, consider replacing it with a new one. It's advisable to change the circuit board (PCB) as well. If you're unsure about electrical testing, consult an expert.
Remember to follow safety precautions when dealing with electrical components. If you're not experienced, seek professional help to avoid any risks. Good luck with resolving the issue!
For reference, the Karcher Puzzi 100 is designed for gentle and effective cleaning of small to medium surfaces, especially carpets and upholstery2. Its spray pressure is around 1 bar, and the spray rate is approximately 0.26 gallons per minute. If you need further assistance, consider referring to the Karcher Puzzi 100 user manual.
4/20/2024 10:55:08 PM •
Dishwashers
•
Answered
on Apr 20, 2024
Can't get dishwasher out from underneath the counter
Question edited to move it from Computers to Dishwashers.
Is there by any chance a floor tile 4" out from the dishwasher front? If so, try lifting the front with a crowbar or long screwdriver.
Did you disconnect, inlet hose, drain and power? They may have been installed tight, or clipped.
..
4/19/2024 6:24:59 PM •
Dishwashers
•
Answered
on Apr 19, 2024
Not finding what you are looking for?