20 Most Recent Amana AOCS3040 Electric Single Oven Questions & Answers

0helpful
2answers

What does the code 5ab or sab mean my cook top

amana oven reads SAb or 5Ab code? stove works, oven doesnt??? HELP
12/31/2014 3:00:59 AM • Amana AOCS3040... • Answered on Dec 31, 2014
0answers
manual
0helpful
1answer

Lock light will not go off

Try unplugging or reset the breaker. Leave it off for about a minute. If that doesn't get it then try to remove face plate. Disconnect the wires to the control panel. It can put it back in order. Next , maybe this should be second, try to google your problem and often times the results are there. I have loved many a problems doing that. Last resort, call mfr and see what they suggest. They may have the easiest and fastest fix.
2/26/2013 1:18:21 AM • Amana AOCS3040... • Answered on Feb 26, 2013
0helpful
4answers

Erroe code 5ab

According to the manual, this mode is SAB and not 5AB. SAB stands for sabath mode and lasts for 72 hours. The mode may be canceled by holding in the clock button for 3 seconds. This mode was activated by holding in the clock button for 3 seconds. My wife did the same thing when resetting the clock for daylight savings time this year. Resetting the power does not reset SAB mode.
7/31/2012 7:50:22 PM • Amana AOCS3040... • Answered on Jul 31, 2012
0helpful
1answer

Oven door will not open

The lock motor (latch) has gone bad. Unfortunately, the part has been discontinued and is no longer available for this model. If you need further help, I’m available over the phone at https://www.6ya.com/expert/jason_4570d45317834dd3
4/25/2012 4:24:50 AM • Amana AOCS3040... • Answered on Apr 25, 2012
0helpful
1answer

Oven is not heating up

Hello & Welcome to FixYa

This indicates an open/shorted oven temperature sensor and to solve this problem the sensor needs replacement. If you want to be sure before replacing the sensor then you can test it with a voltmeter for around 1100ohms....if it reads more than this then it needs replacement however, if the reading is around or less then 1100ohms then it is the control board that needs replacement. Please get back to me if you have any other questions. Kevin

12/19/2011 3:23:48 PM • Amana AOCS3040... • Answered on Dec 19, 2011
0helpful
1answer

Oven door does not fully close

The usual reason for oven doors not closing properly, is weak door hinges,if it does not close all the way, and the door seal is o/k, then I suggest you replace both door hinges. Please rate my solution. Thamks.
11/16/2011 11:44:50 PM • Amana AOCS3040... • Answered on Nov 16, 2011
0helpful
1answer

Buzzing and f2 showing on display panel

Hello,

The F2 error code means that the over overheated by at least 100 degrees above the tempature that was set at the time. The usual reason the oven would over heat by so much is a defective oven tempature sensor and the sensor would need to be tested to see if is the problem to test the sensor it would need to disconnected from the wiring to it and measure the amount of ohms of resistiance AT ROOM TEMPATURE when the oven is off and cool. At room temp. the the meter used to check the sensor should display between 1060-1100 ohms,if the number is vastly different that 1060-1100 at room tempature the sensor is defiently bad and should be replaced. This is what the sensor looks like oldtech2332_129.jpg
it will be inside of the oven chamber and again to properly check it the wiring should be unplugged and the meter leads should be placed into the plug at the end of the sensor to measure the ohms

GENE
10/10/2011 2:26:51 PM • Amana AOCS3040... • Answered on Oct 10, 2011
0helpful
1answer

Oven won't shut off

Hi,Here is a tip that I wrote about why an electric oven will not shut off.Electric Oven Problem Oven will not shut offheatman101
9/30/2011 3:18:33 AM • Amana AOCS3040... • Answered on Sep 30, 2011
0helpful
1answer

I only see 1 element,

unplug unit remove back,,remove tw0 screws holding broil [top] element and replace..
8/29/2011 12:40:24 AM • Amana AOCS3040... • Answered on Aug 29, 2011
0helpful
1answer

The latch on the oven

Hello there and thank you for choosing fixya
This is a fairly common problems with these ovens expecially if you have just used the self clean feature or were using it and tried to interupt the cycle.
What you will need to do is first unplug the power to the oven then wait 1 full hour with out touching it then after the hour is up plug the power back in and you may hear a click sound if not wait additional 5 min then press the cancel or the off button for the self clean feature then try to open the door.
Now if this does not work than the door lock feature is either faulty or stuck which means that you will have to remove the top of the stove and unbolt the plate that is under neath there to get to the switch to release it once it has been released check it out really good to see if any of the wires look or smell burnt or the lock itself looks worn out if so replace it ok
Hope this helps you out
Best regards Mike
8/15/2011 3:24:42 PM • Amana AOCS3040... • Answered on Aug 15, 2011
0helpful
1answer

The oven keeps beeping code

Hi

F4 Error indicates a loose/broken wire on the oven temp sensor or the oven temp. sensor itself is bad and should be replaced. To solve this issue test the oven temp. sensor, it should read between 1080-1120 ohms, if the rating is more then that and the door appears to be closing fine then it is the control board that is bad and should be replaced. Hope this helps...please post back for further assistance.
Daniel

8/7/2011 12:07:51 PM • Amana AOCS3040... • Answered on Aug 07, 2011
Not finding what you are looking for?
Amana AOCS3040 Electric Single Oven Logo

74 questions posted

Ask a Question

Usually answered in minutes!

Top Amana Ovens Experts

Cindy Wells

Level 3 Expert

6553 Answers

Marvin
Marvin

Level 3 Expert

85240 Answers

Brad Brown

Level 3 Expert

19163 Answers

Are you an Amana Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Amana Ovens

  • Amana Ovens

Most Popular Question

f9 code

  • Ovens
Loading...