20 Most Recent Kenwood KDC-MP335 CD Player Questions & Answers


Pueden alludarme tengo un stereo Kenwood kdc mp335 no puedo configurar la salida para el aux au que el stereo trae la salida en la parte de atr?s????

Kenwood... | Answered on Jan 22, 2020


i was in a similar situation today luckily i was able to figure out the solution

follow this

1.switch to STANDBY MODE using the power button on the remote or using the SRC button on the player itself

2.Once you are in the standby mode , press the MENU button ( bass button ) on the left hand side top corner for 1 second

3.Use the right control Knob up and down to switch to CLK ADJ mode .

4.Once you are in CLK ADJ mode Hold the right control Knob for a second until the time starts flickering for change

5.Use the right control knob to change the settings , up and down changes the hour and , left and right changes the minutes

6.Press the MENU button ( bass button ) to save and exit

7.ALWAYS MAKE SURE YOU ARE IN STANDBY MODE

hope this helps :)

Kenwood... | Answered on Jan 25, 2013


The wiring diagram is on page 27 of this manual.

Kenwood... | Answered on Nov 05, 2012


Try checking all of the fuses in your vehicle. You should have two fuse boxes, one in the engine compartment and another under the dash or in a kick panel inside the vehicle.

Kenwood... | Answered on Sep 02, 2012


First check your speakers and speaker wires to make sure you have no shorts and/or grounds. If your speakers and speaker wires are fine, try pressing the reset switch if there is one. It should either be a pencil tip sized indentation somewhere on the face (it will not be marked) or behind a small hole on the subpanel behind the face. If there is no reset switch, you can reset it by disconnecting power to the radio for a few seconds. You can do this by disconnecting one of the battery cables if you can't get to the back of the radio. If that doesn't work you probably have a bad output ic.

Kenwood... | Answered on Sep 29, 2011


on my sportster 5 I held down Menu and Display together for 5 seconds to unlock the demo mode

Kenwood... | Answered on Jul 15, 2011


You can download the manual at
http://www.kenwoodusa.com/UserFiles/File/Global/Consumer/Manuals/KDC-MP3035.pdf

Kenwood... | Answered on Mar 30, 2011


Standard radio color code as follows:RED=switched ignition +12v YELLOw=+12 volt battery(always hot), BLACK= ground, BLUE=remote turn on for amp, OrANGE=light dimmer, White and white/blk= left front , gray and gray/blk= right front, green and green/blk=left rear, violet and violet/blk= right rear

Kenwood... | Answered on Feb 10, 2011


black is ground, yellow is constant and red is switched or ignition.

Kenwood... | Answered on Jan 17, 2011


it sounds like you are using the blue wire (antenna remote turn on) instead of the blue/white (amplifier remote turn on) wire to turn your amplifier on.

Kenwood... | Answered on Jan 17, 2011


are you using an amplifier? if so you may be using the antenna remote turn on wire (blue) instead of the amp remote turn on wire (blue/white).

Kenwood... | Answered on Nov 15, 2010

Not finding what you are looking for?
Kenwood KDC-MP335 CD Player Logo

86 questions posted

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

The Knight
The Knight

Level 3 Expert

76407 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kenwood Car Audio & Video

  • Kenwood Car Audio & Video

Most Popular Question

neeed radio wiring diagram kdc mp335

  • Car Audio & Video
Loading...