20 Most Recent Radio Shack Pro-2096 Base Scanner - Page 6 Questions & Answers

To install a barrel pin jack in a RadioShack Pro-2034 police scanner, you will need to follow these steps:

1. Locate the appropriate input/output port on the back of the scanner. This is typically a 3.5mm or 1/8-inch jack.
2. Gather the necessary tools and materials. You will need a small Phillips head screwdriver, a barrel pin jack, and any connecting wires or cables that are required.
3. Carefully remove the back panel or cover of the scanner to access the internal components.
4. Locate the input/output port on the circuit board inside the scanner.
5. Carefully disconnect any existing wires or cables that are connected to the port.
6. Connect the barrel pin jack to the circuit board using the appropriate wires or cables. Make sure to follow the wiring diagram or instructions provided with the jack to ensure proper connection.
7. Secure the jack in place using the screws provided, or by soldering the connections if required.
8. Replace the back panel or cover of the scanner and test the new barrel pin jack to ensure it is functioning correctly.

It is important to follow the manufacturer's instructions and use caution when installing any components or making modifications to your scanner. If you are unsure about any aspect of the installation process, it is recommended to seek the assistance of a qualified technician or the manufacturer.

Radio Shack Catalog (1988, No. 419, page 64.) https://www.google.com/search?q=Realistic+TRC-412+manual and https://www.google.com/search?q=Radio+Shack+21-1506+manual ..

There is some historical data in the link, but not seeing a manual. https://www.google.com/search?q=Radio+Shack+Optimus+Car+Radio+Model+%23+12-1946 ..

To unlock your Radio Shack Pro-70 Scanner, you can try the following steps:

1. Turn off the scanner by pressing and holding the "Power" button until the scanner turns off.
2. Press and hold the "Func" button while turning on the scanner again. Keep holding the "Func" button until the scanner finishes its power-up routine and the display shows "Program."
3. Use the number buttons to enter the four-digit unlock code. If you don't know the unlock code, try entering "0000," which is the default code for many Radio Shack scanners.
4. Press "E" to confirm the code. If the code was entered correctly, the scanner should now be unlocked and you should be able to access all functions.

If the above steps do not work, try resetting the scanner to its factory defaults. To do this, turn off the scanner, then press and hold the "2," "9," and "MAN" buttons while turning on the scanner again. Keep holding the buttons until the scanner displays "Factory Test." Press the "Func" button to confirm the reset. If none of these steps work, it's possible that there is a hardware issue with the scanner and it may need to be serviced or replaced.

wont receive those freq to old

Question edited for clarity. The manual is here https://rigreference.com/documents/rr-5eb71c9c1e15e4.34936870 https://www.radiomuseum.org/r/radioshack_hyperscan_pro_51_hand_held_scanner_20_308a.html ..

Hi, Please double check that the device isn't close to any antenna's or microwaves when you're using it. Also, you don't want to operate close to any radios or walkie talkies as their frequencies could cause interference. Thank you.

the make has no service manual and fully defunct now and is not a car.

You might not get an answer to this question as in some countries Police scanners are not legal.

Does it have an ink pad or roller cartridge? If it does, you can put a few drops of Ink Pad Ink on it. https://www.google.com/search?q=ink+pad+ink Is it the same as these? The 3011 and 3012 are the same. https://www.ribbonsunlimited.com/category-s/118.htm ..

Question edited for clarity. Question moved from Office Equipment. Owner Manuals and a video that covers 'Stalker Mode'. https://www.google.com/search?q=radio+shack+197+digital+trunking+scanner+manual ..

The speakers and the parts that control the sound and have the sound to come out are broken now after being dropped and should be repaired.

It is a rebranded Sonin Inchmate+ DT110. I found a manual at inspectusa. A better model which can be bought used is the Inchmate pro. It has more features and if you have one of those the manual is at opticsplanet.

We are unable to help on mystery devices. The obvious answer is that the batteries aren't in correctly, or one of the batteries is faulty. Some can go 'reverse polarity'.

I have one I can copy.

sorry but this is not radio shacks tech support

Usually you can edit the scan list, if not you can reset the whole scanner by turning the off radio, turn it back on & hit 0-1-enter & 0-2-enter, this will put it back to manufactory default, then start over again.

I think that google could have video's about what to do and how to fix your pro 508 squelch from Radio Shack.

I don't know, maybe it is faulty or maybe it is telling you what you are trying to measure can't be measured on that range. I suggest you learn more by measuring a few known values to see what happens... I have a Radio Shack multimeter and it was a complete waste of space from day 1 and no better after it had been "repaired" by the Tandy boffins. The readings vary wildly between summer and winter, often only half the display works and sometimes it doesn't work at all until it has been switched on for a while.