20 Most Recent Dremel Variable - Speed Multipro Rotary Tool 395 - Page 9 Questions & Answers


hello,

try to find it here:

http://www.powertoolspares.com/parts2.php?model_ID=3057

may this help.

melnavz

Dremel Variable... | Answered on Jul 23, 2008


threw it in the trash!

Dremel Variable... | Answered on Jun 25, 2008


When the brushes go on my Dremel, it just stops, sometimes erratically - no smell or burning.

Dremel Variable... | Answered on May 23, 2008


There might be many reasons but the one of them is you might be obstructing its air intake passage and it is over-heating.

Dremel Tools &... | Answered on Apr 05, 2020


If the threads on the nut or shaft are stripped, the nut will turn freely and it can be removed with pliers by turning and pulling at the same time. If it won't turn, it is probably galled or cross-threaded. In that case, try penetrating oil first. If that doesn't loosen it, try heating the nut with a butane or mapp gas torch. Good luck.

Dremel Tools &... | Answered on Nov 13, 2019


your best bet will be ebay Then if that's not successful, check with these people
https://www.ereplacementparts.com/search_result.php?q=Charger%2C+dremel+1100
You'll need to know the voltage. The 100 volt charger is discontinued. They carry authentic Dremel parts.

Dremel Tools &... | Answered on Nov 02, 2019


You screw off the collar on the tool, remove the chuck and inner part. The chuck is replaced with a special chuck (no inner piece). The special chuck has a square opening in it's nose that accepts the square end of the flex shaft inner cable. Is is actually a speedometer drive cable, from yesteryear.
Then you pull the inner cable out slightly, if it will, and put the inner cable into the square opening of the special chuck on your dremel motor. once engauged, you carefully screw the outer shaft housing on to the end of your dremel motor.
What you want to avoid is damaging this area during flex shaft assembly. I have had success with turning the output side of the flex shaft, while tightening the outer flex shaft onto the dremel motor. Stop tightening if it starts binding...
Rotation seems to help with alignment of all parts.

Cheers,

Doc

Dremel Tools &... | Answered on Oct 02, 2019


Contact Dremel directly and inquire.

Dremel Tools &... | Answered on Oct 01, 2019


spray lube or oil and use pliers to move it back and forth

Dremel Tools &... | Answered on Jun 03, 2019


Fixya is unable to suggest sources for Dremel parts.

Dremel Tools &... | Answered on May 14, 2019


It's possible that the enameled copper coiling on the stator was compromised when it overheated creating a short. Sadly, unless you have a replacement stator is cannot be fixed. Sorry.

Dremel Tools &... | Answered on Feb 11, 2019


3 in 1 is a light oil used the lubricate small joints, plates and bearings. It can also be used as a releasing oil for stuck bolt etc. 3 in 1 is usually ok to use in small amounts to grease the bearing points on your Dremel.

Dremel Tools &... | Answered on Dec 23, 2018


You can use canned air for light dirt,or compressor with blow gun for heavier dirt.

Dremel Tools &... | Answered on Nov 04, 2018

Not finding what you are looking for?
Dremel Variable - Speed Multipro Rotary Tool 395 Logo

197 questions posted

Ask a Question

Usually answered in minutes!

Top Dremel Tools & Hardware - Others Experts

cluffermon

Level 1 Expert

4 Answers

Mike

Level 3 Expert

4369 Answers

Van Allen
Van Allen

Level 2 Expert

277 Answers

Are you a Dremel Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Dremel Tools & Hardware - Others

  • Dremel Tools & Hardware - Others

Most Popular Question

flexible extension not working dremel

  • Tools & Hardware - Others
Loading...