20 Most Recent
Dewalt DW8306 36-Grit. 4-1/2" Blue Zirconia 7/8" Arbor Resin Fiber Disc - Page 2 Questions & Answers
Model dwe350. How can I remove blade installed upside down?
I think once the retaining screw has been removed the only option open to you is carefully applied brute force - clamp the stuck blade in a strong vice and keeping the assembly straight and the blade under tension apply additional force by levering the saw backwards with a large screwdriver or tyre lever using the vice as a fulcrum.
If the blade isn't kept straight it could snap off.
12/1/2020 4:56:33 PM •
Dewalt Saws
•
Answered
on Dec 01, 2020
Dewalt radial arm saw GW1- Is it single phase or 3 phase
if the plug on the cord fits any other outlet in the house it will be single phase
if the cord is cut , then it will have only 3 wires if it is single phase
( active , neutral and ground )
if it has 4 or more wires it will be 3 phase
most saws running a 200 mm blade or around that size and used for home duty will be single phase
the phase notation will be on the plate attached to the motor of the saw
It will read voltage , amperage, watts or hp, phase and cycles
10/3/2019 3:59:27 AM •
Dewalt Saws
•
Answered
on Oct 03, 2019
DeWALT DWX726 Type 1 Miter Saw stand does not fold down
I think that I have the same model, and yes, I do find the buttons to be of some trouble. In my experience, they can stick, not allowing the leg to collapse. I have to keep them pushed in at the same time collapsing the leg. Look for any burrs or bending on the folding device itself, as it may have gotten bent during a move and needs straightened.
8/6/2019 7:24:58 AM •
Dewalt Saws
•
Answered
on Aug 06, 2019
How to change the blade on a dewalt 12 inch sliding miter saw
Unplug the saw, look for the bolt in the center of the blade and also look for the arbor lock button, if there is no button on the motor, look for the jamb nut on the back side of the blade holder, if there is none you can use a block of wood under the blade for the teeth to bite into. Unscrew the bolt and it may be reverse thread! Remove the blade and the collar, put the new blade and collar on and tighten.
3/14/2019 2:43:51 PM •
Dewalt Saws
•
Answered
on Mar 14, 2019
Does the Dewalt 4 1/2” angle grinder (model DWE4011) have a serial number? I cannot find one on mine.
It should be on the sticker with the model number & other information, if not it's likely on your receipt or original box. I know if you're like me you have no clue where they are, check the area where the battery connects to it also, if no luck just call/email DeWalt or call your Local Lowe's and get a Tool SalesPerson on the line, they'll tell you! I just had the same issue with some Milwaukee Tools that needed warranty repair, I know this is frustrating.
2/28/2019 5:46:17 AM •
Dewalt Saws
•
Answered
on Feb 28, 2019
Dewalt jigsaw (dw321) how to
UNPLUG TOOL. To remove the blade, lift the knob on the top of the jig saw approximately 1/4".
Rotate the knob counterclockwise until the clamp is open (Figure 8a). Do not force the knob once
it stops. Insert the blade as shown. Make sure the back edge of the blade fits into the support roller.
Tighten clamp by turning top knob clockwise until you hear a click. Push knob down.
For "T" shank blades, insert blade to the shoulder of the shank.
Look at manual on the link below.
http://www.dewaltservicenet.com/documents/English/Instruction%20Manual/402086-01,DW321.pdf
Good luck please rate 4 thumbs up and please leave a testimonial
2/6/2019 3:01:31 PM •
Dewalt Saws
•
Answered
on Feb 06, 2019
Not finding what you are looking for?