Sears Craftsman LiftMaster Chamberlain Garage Door Opener Wireless Keypad Model 976LM Security+ - Answered Questions & Fixed issues
2 Answers
I have a Merlin Powerlift-Model 2500L Garage door ...
This is a foreign design but here is what the instructions say to do.
Remove the light cover then remove the colored plastic
rectangle strip located underneath. This will reveal a red Learn/Delete? button.
1. Push Learn/Delete button for 2 seconds the lamp will
blink continuously to alert you that it is in Learn Mode.
2. Push the big button on your remote for 2 seconds
3.Push the little button on your remote for 2 seconds Minimum of 1 second is required between each action
Your remote will now operate with your motor
b) Overhead Doors
Remove the coloured plastic rectangular strip located next to
the Merlin label on the front of the motor. This will reveal a red Learn/Delete button.
1. Push Learn/Delete button for 2 seconds the lamp will
blink continuously to alert you that it is in Learn Mode
2. Push the big button on your remote for 2 seconds
3. Push the little button on your remote for 2 seconds
*Minimum of 1 second is required between each action
Your remote will now operate your unit. Thanks BB
Sears Craftsman...
|
Answered
on Aug 30, 2020
|
9,618 views
6 Answers
Light does not come on when I open/close door, not the bulb
Good Morning:
I also substituted Floescent Bulbs for the standard bulbs. The bulbs would not light up although the relay was working. It seemed that the Florescent bulbs had a somewhat shorter neck. What I did was unplug the drive system from the outlet and then bend the metal connector in the socket so that it would come out further towards the opening of the socket. I then repluged the drive. The Floercent bulbs now have contact and are working perfectly. Simple problem with a simple solution.
Sandman
Sears Craftsman...
|
Answered
on Oct 09, 2019
|
14,220 views
6 Answers
Liftmaster garage door intermittent power loss
I had the same problem. Although it appeared to be the logic board, on mine it actually was the connectors between the logic board and the power supply board.
There are 2 connections on the logic board. One white connector with wires going to the main unit, and another set of connectors that plug directly into the smaller circuit board that holds the step-down transformer (120vac - 22vac). These pins were not making good connection between the boards. I simply bent the pins slightly so they would make better contact on the logic board and have not had a problem since. This must be a weak point on these door openers. Purchasing a new logic board would work too, as the connectors are newer and tighter.
Sears Craftsman...
|
Answered
on May 28, 2019
|
11,559 views
2 Answers
Garage door senser not working
One possible reason. (RF) Interference from an ultrasonic humidifier. The radio wave created to create the mist will cancel out a garage door opener I learned it the hard way I almost replace two garage door opener's but I turned off humidifier and everything worked in my Internet works better now too. Just passing this tip on hope I helped.
Sears Craftsman...
|
Answered
on Dec 29, 2018
|
300 views
3 Answers
Have three garage doors, remote
One possible reason. (RF) Interference from an ultrasonic humidifier. The radio wave created to create the mist will cancel out a garage door opener I learned it the hard way I almost replace two garage door opener’s but I turned off humidifier and everything worked in my Internet works better now too. Just passing this tip on hope I helped.
Sears Craftsman...
|
Answered
on Dec 29, 2018
|
302 views
3 Answers
How to switch back to automatic after manually close the garage d
mikey-moore's advice helped me figure out what to do but it's not exactly what I had to do. Manually open the garage door all the way. Then hit the automatic button you normally would use to open and close your garage door. The bracket slides back and locks into place. Hit the automatic button again and the garage door should automatically close.
Sears Craftsman...
|
Answered
on Oct 04, 2018
|
1,338 views
1 Answer
Key pad will not work to close after it just opened the door
I can't tell if you're question is accurate, are you saying that the key pad will only open the door and never closes it or that it will only do one direction then you have to use the remote? If you're saying the keypad will not close the door at all, that may be a safety issue since closing doors can potentially damage property or worse, if your saying the remote works both ways then you probably need to reset your opener and keypad. Cut the power to the opener, leave it disconnected for five minutes. Reconnect and try keypad again. If this doesn't resolve the problem them you may have a bad circuit and will have to call a pro.
Sears Craftsman...
|
Answered
on Dec 22, 2017
|
156 views
1 Answer
Merlin 230t
If the chain is loose I would definitely tighten it up to remove the sloppiness of the drive. That will in turn help you to accurately find the sweet spot that is currently eluding you. And you have to work fast because you do not want to overheat the motor.
Sears Craftsman...
|
Answered
on Sep 21, 2017
|
325 views
Not finding what you are looking for?
