Top 20
Dewalt DC920KA Heavy Duty Xrp 18V Cordless Drill/Driver Questions & Answers
Dewalt drill melts battery
There may be a short in the motor or wiring, or the gearbox is broken or otherwise seized up. Dewalt provides replacements for most parts at reasonable prices, so it's worth taking the drill apart to find out what is going on. I suspect you will find damaged wiring inside due to overheating; you may be able to identify the problem by seeing where the wire insulation is charred or melted. Unless you have a good drill of the same model so you can compare electrical resistance, it's a bit hard to ID a bad motor with an ohmmeter. However, you can try visual and olfactory inspection - if it looks and smells burned, it probably is. You still should check the transmission to make sure it isn't the source of the problem.
DEWALT com
Why does battery charger blink twice no matter where its plugged in?
You may have a failing capacitor on the secondary side of charger power supply circuitry. The output voltage will be low or have a lot of ripple; this would cause the error detected. Pictured below is a bad electrolytic capacitor next to several good ones (this is not from a battery charger). Notice how the top is bulged upward instead of being flat - it indicates pressure caused by the capacitor burning out.
There are other failures that could cause this error code, but this one is highly probable.
Dewalt dcd950 chuck
Its is about a 2 years modified the XRP chucks In Netherlands the model 950 is not QS made for europe but all the XRP machines have had a special solide looking Chuck For the original Chuck there was a special tool to remove the chuck the gearbox must be open to and a special
N119912 a complete unit of repair tools to remove the chuck and replace , BUT the new modificated repair is by get a normal standard keyless chuck , asked them for about the modification because of the older repair tools and chuck http://www.2helpu.com/world/map.aspx it's about much more cheaper to choose for modification the N119912 is possible renumbered thats possible the right same tool because of the model DCD 950 is not selled in Netherlands . the DCD945 instead of but it means the same kind of modification .
Wher do pin bearings go into the transmission of
if its like my DC925,you have to remove front of trans. toward chuck! its a plastic piece with a s.s. flat spring washer. if washer falls out install from bottom of plastic when removed from trans. bearings stand in gear grooves. make sure if nut falls out match 1 with 1!
Broken dewalt battery
18v lithium ion
When a Dewalt charger is showing a fast blinking red light it means the battery is no longer chargeable. It may be because of a bad cell or short inside the battery. Whatever the reason the charger will not charge the battery and it needs to be replaced.
Revive drill driver battery packs
Rechargeable batteries do have a lifespan, they won't recharge forever. If you have fully discharged the batteries then fully recharged them and they still don't have full power or they only last a couple minutes then they are done. If they won't charge or the charger shows them as defective, the only fix is to replace them.
I bought new batteries for ,my dewalt dw958 drill
I am thinking the switch or motor is bad, check the switch first. you can locate parts at dewaltservicenet.com. Make a wiring diagram before removing anything, these parts are polarity sensitive.
My dewalt 18v xrp battery
Depending on how old or more to the point how many times you have already charged the battery, it may be worn out. All rechargeable batteries do reach a point where they won't charge up anymore. If you have fully discharged the battery and tried to fully charge it up again and it won't take a charge or only lasts a few minutes on a charge it may be time to recycle it and buy a new one.
Dc825 manual
Go to
http://servicenet.dewalt.com/, put your model number in the "find parts" search box. A couple models of the DC825 come up, select yours and on the right side of the product page you can download the parts breakdown and manual.
Need manual to understand basics on Dewalt
you can try and go to dewaltservicenet.com and under the left-hand side you will find an area to download manuals and breakdowns, click on this and then go to manuals in the next page, click to view or download. Let me know if you need more assistance.
Not finding what you are looking for?