Black & Decker BDL500S - Answered Questions & Fixed issues

0helpful
1answer

Who has instruction manual of

I have a copy of the BDL500S Manual, I can email it to you if you like
11/16/2011 8:04:18 AM • Black & Decker... • Answered on Nov 16, 2011 • 217 views
0helpful
1answer

How do i calibrate a black & decker BDL220S laser level

Rotate the laser to center horizontal (H) or vertical (G) bubble vials
9/11/2022 3:59:12 PM • Black & Decker... • Answered on Sep 11, 2022 • 32 views
0helpful
2answers

I have a BDS 300 sensor and have lost instructions

I just bought one too and instructions need deciphering. Select wood or metal with selector switch. Put unit flat against wall. Press and hold on/off button on left. (It looks like it must be kept pressed in at all times to be 'on' and when released it's 'off). The unit with calibrate and give a beep back and lower red LED will stay on. Move unit slowly left/right and more red LEDs light up until green is on. This is 1st edge. Mark it with pencil. Move unit along until Green is off and down to single LED. Then move it back in opp. direction until Green is on again. This is 2nd edge. Attached is a scan of page from Instruction Manual. Quality is lowish as attachment limit here is 150kb.e4edea4.jpg
1/29/2013 10:11:15 PM • Black & Decker... • Answered on Jan 29, 2013 • 8,048 views
0helpful
1answer
0helpful
1answer

I have no laser light when I turn my level on

Check to make sure battery isn't bad first.. If upon changing the battery, it still doesn't work, the laser might be bad or worn out. Good luck... HDTV GURU JAY
3/16/2011 1:51:44 PM • Black & Decker... • Answered on Mar 16, 2011 • 278 views
0helpful
1answer

CHarging light blinking while trying to charge

Battery is old...time for a new one.
9/3/2009 5:12:36 PM • Black & Decker... • Answered on Sep 03, 2009 • 220 views
0helpful
2answers

What do Indoor air quality meters measure?

They measure the humidity, CO2 levels, CO levels, temperature and also the dew point, wet bulb as well as the outside air.
11/30/2022 4:57:13 AM • Measuring Tools... • Answered on Nov 30, 2022 • 876 views
0helpful
2answers

Where can i find the best handyman services for all electrician and plumbing work?

I would recommend Home Advisors or Angies List for your area.
11/22/2022 6:08:22 AM • Measuring Tools... • Answered on Nov 22, 2022 • 567 views
0helpful
1answer

Stanley Fatmax 1000 Peak Amp Power Station. Where can I buy an O ring for a Fatmax 1000A?

You can buy O-rings by size from Home Depot, Hardware stores or any automotive outlet. https://www.google.com/search?q=Fatmax+1000+parts ..
11/18/2022 8:14:13 PM • Measuring Tools... • Answered on Nov 18, 2022 • 17 views
0helpful
1answer

How do I calibrate a Digitech rain gauge. It is reading too high.

Question edited for clarity, two questions made into one. Question moved from Digitech Music to Weather Station Duplicate post deleted in Cars and Trucks. Refresh page to see your question published. Help in the link. All of the weather stations are made by the same company. https://www.google.com/search?q=calibrate+a+Digitech+rain+gauge ..
11/18/2022 7:51:15 PM • Measuring Tools... • Answered on Nov 18, 2022 • 19 views
0helpful
1answer

MY FLUKE T5-600 WILL NOT TURN ON . I TRIED NEW BATTERIES STILL NOTHING. IS THERE AN INTERNAL FUSE AND HOW DO YOU GET TO IT

There is no internal fuse. Return the Fluke for warranty repair. Maintenance Clean the case with a damp cloth and detergent. Do not use abrasives or solvents. Because the inputs are electronically protected, no fuses are required.

T5-600/T5-1000

http://attachments.content4us.com > datasheets PDF Because the inputs are electronically protected, no fuses are required. Page 3. Battery Replacement. Observe the polarity markings inside the battery ... 4 pages
11/2/2022 12:00:33 AM • Measuring Tools... • Answered on Nov 02, 2022 • 45 views
0helpful
1answer

Is there a day light savings time feature on the ModeS82950 weather station? My time keeps jumping g back an hour every time I set it

To set DST to on, you must be in the Time Set Mode. Press the menu key to enter the TIME Set Mode. You can skip over any setting by selecting the enter key.
11/1/2022 4:35:38 AM • Measuring Tools... • Answered on Nov 01, 2022 • 177 views
0helpful
1answer

Valve clearance on intek 20HP v twin

The recommended valve-to-piston clearance is generally 0.080-inch minimum on the intake side and 0.100-inch minimum for the exhaust valve
11/1/2022 4:32:00 AM • Measuring Tools... • Answered on Nov 01, 2022 • 209 views
0helpful
1answer

Outdoor sensor isn;t working

Try to bring the sensor 1-3 meters from the base station. Then remove all the batteries for approximately 20mins so it will drain. Put the battery back as per manual instructions. Leave the sensor and the base station for 2 to 3 hours. If it still does not work, repeat the process.
11/1/2022 4:30:52 AM • Measuring Tools... • Answered on Nov 01, 2022 • 223 views
0helpful
1answer

How do you replace the battery on my gvd-504a?

Try to remove the black cap. You can see there are two button-cell batteries located at the top of the unit. Try to twist it off and pull it straight up. Be noted regarding the polarity.
11/1/2022 4:24:47 AM • Measuring Tools... • Answered on Nov 01, 2022 • 58 views
0helpful
1answer

I have a GE 5805WS6

If your unit was initially working fine and you find that it recently intermittently works with the outdoor unit then unfortunately there is not much you can do. The cause is other type units transmitting on the same frequency, eg: internet. You can try changing frequency, but I found the frequency spectrum here full with wifi / internet modems / cameras, so not much can be done. It does still lock on but there are long gaps of nothing. Perhaps a mod to boost either tx or rx ?
10/31/2022 3:01:48 AM • Measuring Tools... • Answered on Oct 31, 2022 • 3,011 views
0helpful
1answer

AcuRite Iris 06014 PRO+ (5-in-1) Weather Sensor. After ordering a temp. sensor, I realized not one of the readings from outside was being sent or displayed. I have done a reset, it does not work.

Question edited for clarity, full 'make model (what it is)'. Question moved from Cars and Trucks to Weather Stations. Did you change batteries in both the outdoor and indoor units? https://www.google.com/search?q=Model+06014+5+in+1+PRO%2C+no+data ..
10/26/2022 4:12:31 AM • Measuring Tools... • Answered on Oct 26, 2022 • 27 views
0helpful
1answer

Hello, I have 2019 Sokkia DT610 Theodolite. Purchased in 2019 and not used for 2 years. There is E190 appears on display. Please share how to resolve and rectify. Thanks.

Question edited for clarity, full 'make model (what it is)'. Question moved from Computers and Internet to Theodolites. It is an encoder problem. You need dealer service. https://www.google.com/search?q=sokkia+dt610+e190+error+code ..
10/23/2022 1:02:18 AM • Measuring Tools... • Answered on Oct 23, 2022 • 34 views
Not finding what you are looking for?
Black & Decker BDL500S Logo

Popular Tags

1 questions posted

Ask a Question

Usually answered in minutes!

Top Black & Decker Measuring Tools & Sensors Experts

Brad Brown

Level 3 Expert

19165 Answers

Tom Chichester

Level 3 Expert

62329 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

53486 Answers

Are you a Black & Decker Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...