20 Most Recent Black & Decker BDL500S - Page 3 Questions & Answers

0helpful
1answer

How can i get the weather station to communicate with the display center

If it is like mine, the CR2032 battery in the base station only lasts about 6 months, whereas the one in the outdoor unit lasts over a year. Try this though. Remove the batteries from both units. Replace the battery in the indoor unit and then in the outdoor unit. It should re-register it.
6/11/2022 5:06:35 PM • Measuring Tools... • Answered on Jun 11, 2022
0helpful
1answer

Just changed battery in my Swiss army watch now it does not work at all any ideas ?

is battery in correctly. make sure it is not upside down
6/10/2022 6:04:48 AM • Measuring Tools... • Answered on Jun 10, 2022
0helpful
1answer

I am looking for the operation instructions for the Max-Cal 950-201

Fowler Max Cal? not a computer so moved you to tools it is a digital hand Caliper tpol. . sold on ebay from china there are 2 choices, ask your sell for the manual . or google for it. the sales sheet shows this, (google hits) www.fvfowler.com[email protected] it is toy grade, if needs calibration is 3 times cost of new tool $25 it is imported from china, dirt cheap and sold 2 times that. aprox. but the only hope is endless googling for manuals.
6/6/2022 8:41:35 PM • Measuring Tools... • Answered on Jun 06, 2022
0helpful
3answers

Hi. My Stanley IntelliTape 0-77-008 has an 'error'

Mine did the same thing. To fix it I extended the tape all the way out. As I retracted the tape it started working. Try it and let me know if this worked for you.
6/6/2022 12:06:59 PM • Measuring Tools... • Answered on Jun 06, 2022
0helpful
1answer

Good Day... Please suggest me to Calibrate my digital clamp meter MEET MS-37A

From the specification list in your instruction manual; "-Software calibrated, no variable resistor adjustment". Therefore it self calibrates or it doesn't function at all because it is software run.
5/25/2022 7:09:19 AM • Measuring Tools... • Answered on May 25, 2022
0helpful
1answer

Taylor WEC-1502 weather station. how to change the alarm on it please?

Question edited to add make name, which also happens to be mine! The easiest way is just to remove the batteries for 20 seconds. The manual as not good because it is made in China. Alarm Press the UP button on the back of the base unit to toggle the alarm on and off. https://www.google.com/search?q=taylor+1502+instruction+manual
5/21/2022 1:39:48 AM • Measuring Tools... • Answered on May 21, 2022
0helpful
1answer

Acr2000 robinair Hello, I soldered

Do you by chance still have your cd? I need to reload mine as well
5/15/2022 12:30:28 AM • Measuring Tools... • Answered on May 15, 2022
0helpful
3answers

What is hookah?

A hookah is an instrument used to smoke shisha. Shisha is a type of flavored tobacco! Read more on Shisha Heart
3/30/2022 11:16:22 AM • Measuring Tools... • Answered on Mar 30, 2022
0helpful
1answer

Where do i locate my mod # for parts and maintenance.

Whatever mystery tool you have, it is normally on a label somewhere.
3/22/2022 4:04:41 PM • Measuring Tools... • Answered on Mar 22, 2022
0helpful
1answer
0helpful
1answer

Owner manual for Ultronic weather clock

Press the "Down" button to toggle between Celsius and Fahrenheit. Press the "Up" button to turn the alarm on and off. For complete instructions on the Ultronic clock thermometer, see: https://pdfslide.net/documents/ultronic-clock-cl-266instructions.html
3/13/2022 7:10:19 AM • Measuring Tools... • Answered on Mar 13, 2022
0helpful
1answer

Fluke 87V Continuity test; Sometimes a solid beep. Other time a continual rapid on/off beep?

Open the manual. Press CTRL+F and type 'beeps' and press enter. There are 19 mentions. https://www.transcat.com/media/pdf/80vUserManual.pdf The continuity test features a beeper that sounds as long as a circuit is complete. The beeper allows you to perform quick continuity tests without having to watch the display. To test for continuity, set up the Meter as shown in Figure 4. Press E to turn the continuity beeper on or off. The continuity function detects intermittent opens and shorts lasting as little as 1ms. A brief short causes the Meter to emit a short beep. Was there a Diode in the circuit? A short beep sounds if the diode is good (< 0.85 V). A continuous beep sounds if the reading is ? 0.100 V. This reading would indicate a short circuit. The display shows "OL" if the diode is open. and also Enter MIN MAX recording mode. The Meter is locked in the range displayed before you entered MIN MAX mode. (Select the desired measurement function and range before entering MIN MAX.) The Meter beeps each time a new minimum or maximum value is recorded
3/2/2022 11:32:58 PM • Measuring Tools... • Answered on Mar 02, 2022
0helpful
1answer

How do I calibrate the SHEKEL MERAV 2000 Scale ?

HOW TO CALIBRATE SHEKEL MERAV 2000 WEIGHING SCALE
2/21/2022 10:34:54 AM • Measuring Tools... • Answered on Feb 21, 2022
0helpful
1answer

My ozito LMR-025 constantly shows err15 when I try and measure any length

How did you fix it?
2/15/2022 5:54:36 AM • Measuring Tools... • Answered on Feb 15, 2022
0helpful
1answer

I have a HVR505G, it spins up but the green laser takes about an hour or more to light

It's not clear what your question is.
2/3/2022 2:10:16 PM • Measuring Tools... • Answered on Feb 03, 2022
0helpful
1answer

ERROR 190-SOKKIA 230R3 SURVEYING INSTRUMENTS

This error E190 appears when there is excessive moisture. Open all the ports, battery compartments, etc., and dry the instrument well. After drying the error disappeared.
2/3/2022 2:00:30 PM • Measuring Tools... • Answered on Feb 03, 2022
0helpful
1answer

Need help recalibration get a SLR202GR laser level

Hi, all electronic rotary laser levelers have an electronic calibration that you can do yourself, you just need to know the correct algorithm to control the buttons. Look here (https://laslev.com/reviews-laser-levels/firecore/automatic-rotary-laser-level-firecore-fre207r-servo/) for an example of this unit, it describes the entire calibration algorithm for the X-axis and the Y-axis. The buttons may be slightly different, but the principle is the same, I'm sure you can do it, there's nothing complicated there.
2/3/2022 1:44:16 PM • Measuring Tools... • Answered on Feb 03, 2022
0helpful
2answers

Can you detect 12 VDC with the GVD-504A ?

No, the potential is not great enough.
1/5/2022 3:47:37 PM • Measuring Tools... • Answered on Jan 05, 2022
Not finding what you are looking for?
Black & Decker BDL500S Logo

Popular Tags

1 questions posted

Ask a Question

Usually answered in minutes!

Top Black & Decker Measuring Tools & Sensors Experts

Brad Brown

Level 3 Expert

19165 Answers

Tom Chichester

Level 3 Expert

62329 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

53622 Answers

Are you a Black & Decker Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Black & Decker Measuring Tools & Sensors

  • Black & Decker Measuring Tools & Sensors

Most Popular Question

instruction manual

  • Measuring Tools & Sensors
Loading...