20 Most Recent GE Nautilus 24" Built-in Dishwasher - Page 4 Questions & Answers

The safety latch needs adjustment or is loose or worn out if you open the door on door side top you would be able to feel the the safety switch with your finger click on and off it should click very easy if not replace it make sure Dw is off or disconnected.good luck

GE Nautilus 24"... | Answered on Oct 30, 2013

II might need the actual model number. However, you can go to page 9 on this manual and check if the flashing options can fix the problem. I am assuming you have already tried to turn the power off and back on.

The ohter thing to try is the reset sequence. Within 6-7 secs press High Temp/ Heat Dry/ High Temp/ Heat Dry/ High Temp/ Heat Dry. All lights should light up, press Start button to exit.

GE Nautilus 24"... | Answered on Oct 28, 2013

I had the same problem (water remaining in the bottom) after the rinse cycle. FYI my GE Nautilus is 7-years old.
(1) I disconnected the drain tube at the garbage disposal unit (in the sink) and, using a wire coat hangar freed a 'plug' of sludge located at the spot where the drain tube clamps onto the garbage disposal. I blew into the drainage tube to further clear other 'plugs' I observed but could not reach w/the coat hangar.
(2) I unscrewed the Filter/Strainer on the inside (bottom) of the dishwasher; and further removed the inner filter; cleaned both out.
(3) Re-ran the dishwasher thru complete wash/rinse cycles (to check for leaks. There were none.
Finally, upon completion of the w/r cycles there will always be a small pool of water (residing in the filter area). However my dishes are clean and (after 7-years) checking the drain tube and filters was a breeze.
Hope this helps

GE Nautilus 24"... | Answered on Oct 09, 2013

The washing filter and disposal is in the bottom of the machine under the spray bar.

GE Nautilus 24"... | Answered on May 27, 2013

Its old get a new one these are not designed to last more than yours did.

GE Nautilus 24"... | Answered on May 02, 2013

the dishwasher should be level.....with the door open check this with a level held against the vertical metal frame at the front side of the dishwasher (where the door seal is attached). Adjust the front leveling feet....one at each side until the front is vertical.....you will probably need a wrench to do this as the feet/bolts are usually quite tight. Be sure both feet are touching the floor when you are done.

GE Nautilus 24"... | Answered on Mar 24, 2013

There is a pump motor underneath with an impeller that is most likely stuck. You will need to turn the impeller until it breaks loose if it is stuck. This is a common problem with GE dishwashers and I recommend that you run it at least once or twice a week to avoid this problem in the future, even if you have to run it empty.

GE Nautilus 24"... | Answered on Jan 31, 2013

From what Ive read, a common fix for this is to clean the door gasket really good. Food particles, dried up detergent,etc,,, all can prevent the door from sealing correctly. I would also inspect the gasket real good and make sure there are not any rips or tears. And finally, I also read using too much detegent may cause this so make sure you are using the correct amount. I hope this helps. Good luck.

GE Nautilus 24"... | Answered on Jan 21, 2013

what is your problem you are Experiencing right now

GE Nautilus 24"... | Answered on Jan 17, 2013

Not finding what you are looking for?
GE Nautilus 24" Built-in Dishwasher Logo

887 questions posted

Ask a Question

Usually answered in minutes!

Top GE Dishwashers Experts


Level 3 Expert

4369 Answers

Nathan Van Boven
Nathan Van Boven

Level 2 Expert

206 Answers

Bill Johnson

Level 2 Expert

306 Answers

Are you a GE Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GE Dishwashers

  • GE Dishwashers

Most Popular Question

gsd4200 will not clean dishes all

  • Dishwashers