20 Most Recent Insignia NS-DA1G MP3 Player - Page 7 Questions & Answers

I found code 85 to work everything but source select.

If your TV has HDMI in and digital optical out, run your HDMI cable via HDMI out on box to, HDMI in on TV then, run digital optical ouyt from TV to digital optical in on reciever. Your reciever has video pass through but, not the best option. Video components should run to TV then out to reciever. If you do not have digital optical out on TV, you may be able to use RCA.

There are no best (as in tweaks) settings for digital connections. They either work or they don't. The manuals for all involved products tell you how to make them work. Without specific make/model info we can't get into any details. Your source material and its selectable audio options will determine what bitstream is transmitted out to your audio equipment.

I am having the same problem. any solution ?

Find the manual and read it.

http://insigniaproducts.com/support.html

I'm assuming that you have tried to reset the radio with the button on its side and it didn't work. In that case this isn't a software - or commands - problem that can be fixed with owner commands, it's hardware: the processor of the radio got stuck because its firmware got corrupted.
All you can do is to force a complete reboot: with the radio working disconnect the battery; join the battery pin connectors for an hour to discharge all residual electricity from it (use a small piece of tin foil); plug it back - if the processor is still operational and the firmware chip intact the full reboot will take place and the radio should start functioning correctly. If this doesn't happen then the radio has failed - not worth repairing, just get a new one.

lacking a remote only means that you would have to manipulate its front panel controls to manage it via menus. Determine the manufacturer and model and look for the manual that would explain how to do that. Or just turn the TV on and start hunting through the menus using the navigation controls it probably has.

Or look for a remote:

If you know the model of the device (which you did not mention) try here:

http://remotes.com/store/codes_original.html

http://www.electronicadventure.us/

or eBay: search for "(model) remotes", check the 'include description' box. Usually cheaper than the vendors.

No. It has only two amplifier channels and the speaker A and B terminals just share physical access to them for two pairs of speakers. It's not four amps.

Here is the manual for you:

http://dl.owneriq.net/f/fabd1491-37f0-4b34-7d08-cdf7feafd4ce.pdf

Good luck!
gylacz

1.CHECK YOUR CABLES PROPERLY
2.UNINSTALL YOUR AUDIO DRIVER AND INSTALL IT AGAIN
3.CHECK YOUR SPEAKER WITH YOUR ANOTHER PC
4.MAY BE IN SOUND OPTIONS U MIGHT HAVE MUTED IT.UNMUTE IT

Generally speaking, an amp protects itself from heat, shorts and overloads by refusing to turn on or stay on. Check for loose speaker connections.

Overloads can be from excessive periods of high output and shorts would be wiring issues or a speaker blowing up.

You should be able to feel if it's hot. WHY is it overheating? Make sure it has sufficient ventilation on all sides and that vent holes are not blocked by dust balls. Ensure the fan (if equipped) is running as designed (some only operate on demand). Clean dust and debris from it.

If the amp comes back on after cooling, you're lucky. They only have so many self-protection cycles in their lives so continuously resetting or cycling their power without addressing the cause can do more harm than good.

If it protects immediately on a cool power up you should disconnect the speaker connections and try it 'naked'. If it comes up then diagnose which lead(s) are shorted. If it does not come up the problem is internal and should be left to an experienced hands-on tech.

Please explain the exact problems you have and the manufacturer and model of the device ..from that number you posted I have no clue what kinda device it is..and what you want to do ..

geez, i dont know.

try swapping the speakers around if the problem still persists either the speaker is faulty or the speakers plug/outlet is usually at the back of the computer you will have to open up the computer to check the lead attached to the rear of the input plug make sure the connection is good or you might have to clean the dust from your computer dust causes static which causes your computer to overheat and all sorts of problems be sure to wear an anti static earth strap before touching anything inside your computer

have you tried this control panel sounds and audio,volume,advanced,speakers select the appropriate speakers from the drop down list or click start control panel administrive tools computer management device manager scroll to system devices + to expand,system speaker right click properties then select use this device (enable) hope this helps

Some specific makes and models would help us find you the manuals so you could correct the problem yourself. Try retero.com

There's no such thing as plug n play in multichannel digital audio receivers.

http://insigniaproducts.com/cms/documents/NS-HD01%20UM%20EN.pdf