Sylvania LC370SS8 Television - Answered Questions & Fixed issues

There is nothing wrong with the TV. It has to do with the signal from the cable TV provider. I got a new cable box and it helped, but still get some freezing once in awhile.

check if you can down load this manual and check page 35. http://data.manualslib.com/pdf/17/1675/167466-sylvania/lc370ss8.pdf?0099fed34b9f7b0871613a4d97ce394b&take=binary The power reset can be done by taking the mains power cable out and reconnecting after 30 secs.

You can't do this without a remote control

Hello
Three digit universal remote codes for Sylvania TV are:
004/ 008/ 009/ 062/ 068/ 069/ 074/ 075/ 076/ 077/ 133/ 161/ 163
Four digit universal remote codes for Sylvania TV are:
0062 0004 0009 0135 0189 0183 0227 0456 0008 0068 0075 0141 0161 Direct Code Entry

1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.

Hi,

Your power supply board is dead, u know basic electronics' and soldering? Most of the times, the power supply board just have dead leakages gases capacitors.These capacitors always bulges up on it top,or puff up on it top.Replaced these gases leakages capacitors will get your TV power stable,and work again.Or tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.

Good luck in solving the problem....

You have a defective shunt regulator. This will cause your TV to come on for 1 or 2 seconds as you describe. The IC650 is bad. The B + supplies fail to switch to full power.In layman garb, you will need a new or refurbished power supply board. There is nothing wrong with a refurbished board.A refurbished board has been tweaked (reworked to optimum performance)and many times will out live a new board. Find an authorized Philips TV shop, show them this note. Good information may result in a reasonable repair. Thanks for asking and show all hands of support!

More detail please, What did you do before your TV went off. Check the switch and the plug.check your remote batteries.

Universal codes are in ur tv univeral remote manual already.None of those codes work for ur tv brand.None of the codes people give u will work either.Return the universal remote where u bought it.Try website like Remotes.com to buy the tv original remote.

Here is a link to a site that you can order a remote for your television! It will cost you about $20 and it's free shipping!!!
http://www.emtcompany.com/sylvania-lc370ss8-remote/rc64.html
I hope I could assist you in solving your problem! Please rate and comment on the solution!

did you ever get it mounted? i am having the same problem myself with my LC370SS8. [email protected]

I had a similar problem with my Phillips 42 in. LCD HD TV.

Here's the problem. The Power Supply Board. I opened my TV up(warranty was up of course) and found several bad capacitors. Phillips and several other companies were sold capacitors that although were highly rated failed within 5 years because of a lack of preservatives. All sorts of electronic equipment is now being effected due to these defective capacitors.
Solutions?
1. Take it in and have it fixed
2. Open it up, check the board for faulty capacitors(bulged or leaking) Buy a new Power supply board and install it.
3. Remove PSB, remove faulty capacitors and replace with compatible new ones.

Hope this helps

IT IS A INVERTOR BOARD FAULT OR LOOK FOR SWOLLEN CAPACITORS ON POWER SUPPLY BOARD IF THERE ARE SUSPECTED CAPACITORS REPLACE THEM WITH NEW ONE IF NOT REPLACE INVERTOR BOARD.

hi! i have a couple of codes here for your sylvania tv, just try them hope it would work! goodluck! 0062 0004 0009 0135 0189 0183 0227 0456 0008 0068 0075 0141 0161

Yes it can be mounted. you can purchase an universal mount that comes with all hardware necesary to install the LCD to the wall.

Try the 211; 212 ;224or 553;604 codes.

http://www.sylvaniaconsumerelectronics.com/pdf/om/LC370SS8.pdf

Okay you need a remote control code witch are diffrent depedning on the universal remote you have. Now you can look up this code by simply going to the manufacture but that code does not hold true with all universal devices. Best thing to do here if you need a remote that really works www.remotes.com would have a answer for you. I use them all the time. But as far as the defualt codes for this TV please contact manufacture you be glad you did.


thanks and please rate.
Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

Universal remotes never work good anyway. You will need the original remote anyway to work the different functions for the TV.

The cheapest that I can find one for you is at NewRemoteControl.com, it's $32.95
Here is the link for you:
SYLVANIA LC370SS8 LCD TV REMOTE CONTROL

No, because screen casting wasn't invented and it isn't a Smart television. Time for a new one.

Here are some troubleshooting tips to try. However, as it is an older set, if these tips fail, the cost of a repair at a shop might exceed the value of the TV. In short, a new TV may be in the works. Cross your fingers. One of these tips may work. Let's troubleshoot the issue and try to get it working: If you are using a remote, check the batteries in it. If you are using several remotes with it, try the alternative remote. Sometimes there is a glitch affecting the remote for a Roku where it won't turn on the TV other than a powered black screen and you have to use the other remote to turn it off and back on and then the Roku screen pops up. I have not sorted out why. Check Power Cord and Connections: First, ensure that the power cord is securely plugged into both the TV and the electrical outlet. If you suspect a faulty power cord, consider trying a different one. Reset the TV: While most Sylvania TVs don't have a dedicated reset button, you can perform a manual reset: Unplug the TV's AC adapter from the electrical socket. Press and hold the Power button on the TV for 20 seconds. Plug the AC adapter back in and turn on the TV. Check Audio/Video Cables: Inspect the audio/video cables connecting your TV to the satellite or cable receiver. Ensure that the color-coded prongs match their respective connecting points. Correct any mismatches (e.g., white cable into a red port) by reorganizing the prongs. Inspect Coaxial Cable: Look for the coaxial cable on the rear side of the receiver, attached to the port labeled as ANT IN. Confirm that the connection is firm; a loose coaxial connection can cause display issues. Tighten the cable by pinching the silver band on the end and rotating it clockwise until secure. Check for Interference: If distortion continues on the TV screen, consider nearby interference. Power-hungry appliances can cause electronic interference, affecting display quality. Visit a Repair Shop: If the above steps don't resolve the issue, you may need professional help. Some technical faults, such as a blown fuse or faulty capacitor, require expertise in dismantling and soldering. If uncomfortable with such tasks, consider visiting a repair shop