20 Most Recent Westinghouse SK-32H240S Television - Page 2 Questions & Answers

yes, it has pip. Use the menu to select the pip setting.

It seems that your unit has some sort of Video side, PSU fault, or a problem to the Video section that is shutting down the Power Supply Unit, PSU. This happens so that no further damage, and possible fire will occur.
You need to take the unit to a reputable service centre/man and ask for a firm "Quote" for the work to be done.

Westinghouse TV SK-32H240S http://legacywd.com/pdf/111_User_Manual.pdf

Its not on or you cannot see it?

problem in the vertical section, check for burnt vertical ic or bad capacitor near the ic.

Possibly it is just the input that has been changed. Find the input and press that a few times to cycle through. If that does not work I will check back and ask some other questions to get this resolved.

Switch off TV, switch off power, remove plug and wait for 48 hours and retry.If problem persists, I suggest it is better to refer it to a qualified service technician, since the back cover has to be opened for investigation/rectification.

the board will be hard to locate but run between 80- 150 if you can find them. However your symptom is most likley cause by one of the Transformers. Which you can get replacement transformers from www.tvrepairworld.com send them a email from their website by hitting the contact button on the right side.

The voltage source to back light inverteres are from the main power supply regulator board. Check it.

This problem is caused from a problem with the main board. The main board will need to be replaced. It runs from $100.00 to $150.00.

Download the user manual to this set. It will have all details. to download it, click here.

Either the lens on the front of the set for the remote receiver is dirty etc or the infrared receiver in the set is bad.The having to get very close and the fact more than one remote reacts this way means the trouble is the receiver is bad.I have seen this a few HUNDRED times in my career.

Are they torc"s---look like gear teeth inside or some odd shape?Take a look a Home Depot in the tool department or your local hardware store

Happy to help get that fixed right away!

You mentioned that your TV is not recognizing the DISH Network signal, since wedo not know how many TV's your receiver is able to support, or whether it's theTV1 or TV2 having the issue I will address them both.

The first thing we want to do is ensure that all connected components arepowered on (VCR, DVD Player, etc.). Check what channel or input your TV iscurrently on by powering the TV off then back on and noting the channel orinput that appears on screen when the TV is powered on.

If TV1:

Check what type of cable is used to connect the TV to the receiver. If you areusing a Coax Cable to connect the receiver to TV1, check the receiver'sback panel for the output name. If your receiver has a "TV CH 3/4Out" (non-ViP Receiver): Tune TV to channel 3 or channel 4,if it has "Home Distribution" output (ViP Receiver): Tune TVto channel 62 or 75. If using non-Coax (RCA, Component, orHDMI) to connect receiver to TV1, cycle through the inputs until pictureappears; most TVs have a "TV/Video", "Input", or"Source" button. If the issue persists, check that theconnections between your DISH receiver and your TV are secure then reset thereceiver by unplugging it from the outlet for 10 seconds then plugging it backin. If not fixed then connect another component (VCR, DVD Player, etc.) to thesame TV, using same cable, same input, and same channel to see if it works. Ifit works with the other component then call us at 1-800-333-DISH (3474) foradditional troubleshooting, if it still doesn't work with the other componentthen the cable should be replaced.

If TV2:

Access "Modulator Setup" from TV1 by pressing the menu button(on the top left of DISH remote) then pressing the numbers 6-1-5. Tune TV2 tothe channel that appears under "TV2 Out" on screen. If stillno picture, verify the mode (air or cable) that TV2 is on. Then change themodulator setup to match this mode (air or cable). After changing modulatorsetup, tune TV2 to the channel that appears under "TV2 Out" onscreen. Check that the connections between your DISH receiver and your TV aresecure then reset the receiver by unplugging it from the outlet for 10 secondsthen plugging it back in. If not fixed then connect another component (VCR, DVDPlayer, etc.) to the same TV, using same cable, same input, and same channel tosee if it works. If it works with the other component then call us at1-800-333-DISH (3474) for additional troubleshooting, if it still doesn't workwith the other component then the cable should be replaced.


Phillip Chang
DISH Network Customer Service Representative