20 Most Recent Stanley 77-730 Fatmax[r] Stud Sensor 400 - sty77730 77730 - Page 5 Questions & Answers


satreece,

The only location that you can get service for the Stanley COMPULEVEL is from Technidea Corporation. A standard factory recharge for the Stanley COMPULEVEL 35-100 Elevation Measurement System is $150.00 and includes a thorough evaluation, R&R of the liquid, recharge of the pressurizing gas, testing, cleaning and repackaging, and complimentary return shipping via UPS Ground to all locations in the US and Canada.

An electronics upgrade is also available for your COMPULEVEL, allowing 2X faster and 3X more accurate measuring and significantly more stable readings. COMPULEVEL upgrades start at $195.00, plus the cost of the standard recharge.

For detailed instructions on how and where to send your COMPULEVEL for service, please visit www.ziplevel.com and click on the 'Service' tab at the top of the page. If you would like to upgrade your COMPULEVEL, please include a brief note with your unit when you send it in for service.


Contact information for Technidea is below.



800.805.LEVEL
760.480.4740 Office
760.480.4738 Fax
[email protected]
www.ziplevel.com

Stanley... | Answered on Jul 17, 2009


The level is meant for 360* of USE not from one single position check both horizontal and vertical... I think that one is a Moveable

Laser? Level?
OH I just found .. is it on a tripod like attachment? there should be a small round "level" on the physical Base of the level itself .... (like the ones your drill would have for drilling down into the floor boards) You must level it that way First.... then you can use it ...

Stanley... | Answered on Oct 26, 2008


5505E MEASUREMETER BATTERY CHANGE (3V CR-2032)
REMOVE WHEEL AND SHAFT BY GENTLY PULLING AXLE OUT OF UNIT.
DRILL OUT 7 PLASTIC HEADS WITH 3/16 DRILL BIT. (ABOUT 1\8 DEPTH)
SPLIT TWO SIDES OF CASE AND REMOVE HANDLE.
SLIDE OUT CLEAR PLASTIC CONTROL UNIT. PUSH DOWN ON BUTTONS AS YOU REMOVE SO AS NOT TO DAMAGE THEM.
PUSH DOWN SLIGHTLY TOWARD THE CASE ON LOCK TABS WHILE GENTLY PULLING CASE APART. START ON ONE END AND WORK YOUR WAY TO OTHER END. KEEP GASKET INTACT. OPEN CASE.
THERE IS A "Y" SHAPED RETAINER HOLDING IN THE BATTERY. WITH NEEDLE NOSE PLIERS, CAREFULLY SLIGHTLY SQUEEZE THE BOTTOM OF THE "Y" AND PULL UP GENTLY. YOU CAN NOW REMOVE THE BATTERY AND INSTALL THE NEW ONE. PUSH RETAINER DOWN TO LOCK BACK IN.
MAKE SURE GASKET IS IN PLACE AND PUT CASE BACK TOGETHER, MAKING SURE WHEEL ADAPTER IS IN PROPER PLACE. TURN ON AND TEST CONTROL UNIT AND TURN WHEEL ADAPTER TO MAKE SURE UNIT IS WORKING PROPERLY.
SLIDE CONTROL UNIT BACK IN BEING CAREFUL OF THE BUTTONS. RE-ASSEMBLE HANDLE AND PUT THE TWO SIDES OF THE CASE TOGETHER. I USED THREE PIECES OF ELECTRICAL TAPE TO HOLD CASE TOGETHER. ONE ON THE TOP BETWEEN THE TWO HOLES, ONE ON THE BOTTOM JUST ABOVE THE DISPLAY, AND ONE IN THE MIDDLE.
PUT THE PLASTIC PIECE IN THE HOLE AND LINE UP. MAKE SURE BOTH O-RINGS ARE ON THE AXLE SHAFT. GENTLY INSERT AXLE ALL THE WAY IN WHILE ROTATING IF NECESSARY.
I WAS SO HAPPY I HAD IT ALL BACK TOGETHER AND WORKING, I HADN'T TAKEN ANY PICTURES AND I DIDN'T FEEL LIKE TAKING IT ALL APART AGAIN. MIGHT ADD PICTURES LATER IF NEEDED. I HAD BEEN LOOKING FOR YEARS ON HOW TO CHANGE THE BATTERY, AND I FINALLY MADE UP MY MIND THAT I WAS GOING TO DO IT.
JMS 10-20-2020

Measuring Tools... | Answered on Oct 21, 2020


You can try the following: 1# Check the main power cable & make sure it has 110V (Do not run the machine with long extension cable).2# Check all harness connection.3# Check keyboard cable connection on back of control board.4# If all the cable connection is good then you may need to replace the control board.

Measuring Tools... | Answered on Aug 02, 2020


Those are precision devices and require factory check up and calibration at regular intervals. Contact your dealer.

Measuring Tools... | Answered on Aug 01, 2020

Not finding what you are looking for?
Stanley 77-730 Fatmax[r] Stud Sensor 400 - sty77730 77730 Logo

1 questions posted

Ask a Question

Usually answered in minutes!

Top Stanley Measuring Tools & Sensors Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Lawrence Oravetz

Level 3 Expert

10548 Answers

Vernon Taylor

Level 3 Expert

7189 Answers

Are you a Stanley Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Stanley Measuring Tools & Sensors

  • Stanley Measuring Tools & Sensors

Most Popular Question

plug stanley fatmax 450 air compressor

  • Measuring Tools & Sensors
Loading...