Kyocera FS-C5030N Led Printer - Answered Questions & Fixed issues


LSU cleaning motor error

When the LSU cleaning motor

is driven, an error signal is

detected continuously for 1 s.

Defective connector

cable or poor

contact in the connector.

Reinsert the connector. Also check for continuity

of the connector cable. If none, replace

the cable.


Kyocera... | Answered on May 27, 2019 | 3,974 views


check the fuser or drum with out seeing the copies its hard to tell for sure

Kyocera... | Answered on Aug 06, 2014 | 121 views


please replace cartridge chip

Kyocera... | Answered on May 10, 2014 | 59 views


replce the toner chip

Kyocera... | Answered on May 10, 2014 | 47 views


there is a blue mark on the right side of the fuser simply pull it towards you and that should allow you to see the rollers and remove paper if not its four screws and three connectors to remove the whole fuser

Kyocera... | Answered on Jul 10, 2014 | 133 views


you are overcomplicating it... all you need is a compact flash card big enough for the firmware... then you upload the firmware to the card and stick the card into the printer... but first power down printer and plug it out and then turn it on and follow the display... it will prompt you

here is the steps...

you will see ready
then press menu... arrow down to memory card
press forward arrow
you will see format
press enter
you will see processing
when its finished
you will see ready...
turn off machine... unplug it...
pull out compact flash
plug machine in
turn it on...

the **** for the compac flash is on the right hand side at the bottom by the ventillation opening...


I’m happy to assist further over the phone at https://www.6ya.com/expert/norman_d2fa496dce30c65d

Kyocera... | Answered on Oct 27, 2012 | 1,265 views


seems vey used maybe you have to bring it to a check

Kyocera... | Answered on Apr 26, 2012 | 292 views


yellow toner motor over voltage. 3 solutions 1 replace toner , 2 replace toner motor, 3 replace engine board

Kyocera... | Answered on Jul 22, 2011 | 151 views


Idea: You can look up the failure codes online in the Kyocera website. Just download the maintenence manual.

Kyocera... | Answered on May 18, 2011 | 2,564 views


You need to reset the toner counter. This is done through the Menu button and selecting Life Counters. The instructions on how to do this are found in the Advanced Operators Guide on page 2-75. The link below will take you to the manufacture's website where you can download it.
http://usa.kyoceramita.com/americas/jsp/Kyocera/resource_details.jsp?pid=14192&rid=14764


Resetting the Toner Counter

The toner containers must be replaced when the printer displays the Low toner or Replace toner message which will be given depending on the color of toner. The Low toner message will be shown as a pre-warning that the toner is running out and the printer will soon stop, at that time showing Replace toner. If you replace the toner container before Replace toner is displayed, you must manually reset the toner counter as explained below. Note that if you reset the toner counter before the toner container is replaced, the subsequent toner warnings will not be indicated correctly.


I hope this is helpful,

Shawn

Kyocera... | Answered on Mar 15, 2011 | 820 views


http://www.kyocerasupport.co.uk/index/download_center.false.driver.FSC5030N._.EN.html#


manual for ur printer

Kyocera... | Answered on Dec 03, 2010 | 204 views


I think that you have used the lens cleaner and then have not pushed it all the way back in.

Kyocera... | Answered on Nov 18, 2010 | 416 views


It looks your waste toner box is full. Waste toner box collects toner drawn during printing. You have to remove waste toner bottle and empty it.

Follow the instructions to clean up toner bottle
http://www.kyoceramita.co.th/news/products/img_promain/20091141129533.pdf

Hope this helps

Kyocera... | Answered on May 21, 2010 | 3,627 views


Replace the black cartridge.

Kyocera... | Answered on May 07, 2010 | 83 views


please open drum unit and there you can find a unit called charge unit inside this one thine wire is coming clean that wire and check ...... if you want full details please chat with me ... my ID [email protected]

Kyocera... | Answered on Jun 14, 2013 | 346 views


you need to scroll thru your menus...paper handling section...make sure mp tray is set to FIRST..that way it will pull from the mp tray untill it is empty than switch to your cassette

Kyocera... | Answered on Jan 06, 2010 | 1,035 views


there are a good few possibilities... your cheapest route is to call a local service tech... anything I tell you is going to cost you more... call him and see what he says... but I am leaning towards bad ram best case and worst case a blown main board...

I’m happy to assist further over the phone at https://www.6ya.com/expert/norman_d2fa496dce30c65d

Kyocera... | Answered on Dec 24, 2009 | 1,506 views


check the paper size settings.if you are using custom paper sizes, you have to specify the sizes on the printer, otherwise it will think that it has a standard paper size

Kyocera... | Answered on Dec 24, 2009 | 550 views


the charger is broken...

I’m happy to assist further over the phone at https://www.6ya.com/expert/norman_d2fa496dce30c65d

Kyocera... | Answered on Dec 23, 2009 | 231 views


close the back cover... or if its broken tape it down...

I’m happy to assist further over the phone at https://www.6ya.com/expert/norman_d2fa496dce30c65d

Kyocera... | Answered on Mar 31, 2011 | 204 views

Not finding what you are looking for?
Kyocera FS-C5030N Led Printer Logo

72 questions posted

Ask a Question

Usually answered in minutes!

Top Kyocera Office Equipment & Supplies Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Timothy Van Der...

Level 2 Expert

152 Answers

Are you a Kyocera Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...