Top 20 Lexmark E250dn Laser Printer Questions & Answers

Over time the rollers get slick and hard. If one side is slick and the other edge is not, it will grab paper sideways and you get a paper jam. Get some rubbing alcohol and rub the rollers (completely all around) to get some debris removed. Some rollers require a slight rubbing with an abrasive pad.

Probably you need to purchase new one - Lexmark E250X22G photoconductor. Every 60000 prints you need to change it or If it is OPC drum (green roller) damaged.

You should be able to go to the control panel and search for new devices. If that does not work then go to the Lexmark site and download the software from that site. It will then handshake with your computer.

.. add paper ?

There is a sensor relay arm under the body of the printer in the hole created by removing the paper tray. Look for a long thin peice attached to a spring assembly. There is a wire that plugs in to the relay it may be loose. You might also remove the paper, push the metal peice of the paper tray into a locked postion and then replace your paper

Make sure to enable that under printer properties. Just go to Printers and Faxes > Right Click on the Lexmark icon > Properties > Configuration > Check Tray 2.

Visit: http://support.lexmark.com/index?locale=EN&page=product&userlocale=EN_US&productCode=LEXMARK_E250D&focusedTab=DOWNLOADS#1Then select the Operating System from drop down to get the appropriate driver for your Operating System and install it.

If the light flashing is the "light bulb like button" or the "Ready/Light" button, it means that either the printer is:• The printer is busy receiving and processing data or printing.• The printer is printing a directory, font list, menu settings pages, or Print Quality Test Pages.If it's Busy:• Wait for the message to clear.• Press and release Cancel to cancel the print job.• Press and hold Cancel to reset the printer.If it's printing a directory, a font list, menu settings pages, or Print Quality Test Pages:• Wait for the pages to print. The Busy message is displayed as the pages print. The Ready light is on when theprinting stops.• Press and release Cancel to cancel printing.• Press and hold Cancel to reset the printer.

You can download the Lexmark printer drivers from theirsupport WEB site. Please click on this link and select your model printer todownload :-http://support.lexmark.com/index?page=home&locale=EN&userlocale=EN_US&segment=DOWNLOAD

A replacement is needed for the following parts:40X2838 Media (ACM) drive assembly40X5930 Media feed ACM clutch CBM40X2853 ACM drive shaft assembly Please contact Lexmark Technical Support for further assistance.

As a last resort you can uninstall and the reinstall the printer

My work-around for this problem is to feed paper in manually through the front. I turn the printer off and make sure all paper is out of the printer. When you turn the printer on - and the blue light stays lit (if it doesn't turn it off and wait - I've had to wait quite some time sometimes).. then manually feed 1 sheet of paper in the manual feed tray at the front. When the paper is inserted... you should be fine to print - and keep feeding paper in until you get your job. If you miss - you might need to hit the "continue" (triangle button)..
I've been trying to find out why mine locks up - and why it keeps jamming - but this is a tried and proven menthod - althought it is annoying it might help you for now.. Good luck

Please print a network settings page to check status if it is connected. To print network set up page click the link http://bit.ly/pvTBgZ

Please take note of the IP address and type it on your browser

The printer has a service error, and printing has stopped. Press Continue twice to see the secondary code. The secondary code will indicate where to locate the problem.

For further assistance, please contact Lexmark Technical Support.

Please power down the printer. Normally, this should correct the problem.
For further assistance, please contact Lexmark Technical Support.

Follow these steps: 1. Press the "Operator Panel" button to print a Network Setup page.
2. Locate the entry labeled "UAA" or "Physcal Address."
3. Write down the 12-digit address. An example is "00:1A:2B:3C:4D:5E."
Set the IP Address 1. Insert your Lexmark drivers CD and select "View Documentation."
2. Select "Software and Utilites" and click "IP Setup Utility" to start the program.
3. Enter the physical address for the printer in the "Discover Print Servers" field and click "Discover."
4. Select the printer from the "Configure Print Servers" list and click "TCP/IP Settings."
5. Click "Suggest Address" if you'd like the utility to locate an available IP for you, or enter the IP of your choice in the "IP Address" field and click "OK.

Please try to download and install the correct drivers from support.lexmark.com website, make sure you filter the correct operating system.

If the error light does not go off, please press the continue button to display the secondary error codes.

For further assistance, please contact Lexmark Technical Support

What you need to do is reset the Network Settings, to do this please click on the link http://bit.ly/kR1jke

Please contact Lexmark Technical Support for additional assistance