Go to Start / Run and type in "services.msc" without quotation marks, then press Enter or click OK.
In the window that opens (Services) look for "Print Spooler" on the right
Right-click "Print Spooler" and select "Properties".
Click on the "Recovery" tab and change all 3 drop-down boxes to "Restart The Service".
Make sure the 2 text boxes underneath say "1" in them.
Click Ok until you are back at the Services window, close it and you're good to go.
Go back into the properties of the "Print Spooler" tab and be sure to click Start to restart the Print Spooler service and it will restart the service immediately.
The Print spooler depends on the Remote Procedure Call (RPC) service. Is this service disabled? Go to services.msc look for RPC. Check state: Automatic
Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks
Opem cartridge door
5100 is a carriage error, check the timing strip for contamination(plastic strip about 1/4" in width) The unit is not homing, check for obstructions on carriage path (iron rode). Please see blow video to locate "carrage"
Here I
will show you where to find drivers and manuals for the Canon Pixma Mp810 photo
all in one printer.
Drivers for this printer are available for Windows
98, windows ME, windows Xp, Windows Vista, windows vista 64bit editions,
windows 7 and windows 7 64bit editions.
On the Mac side drivers are available for Mac OS X
10.2/10.3/10.4/10.5/10.6
A full on screen manual, quick start guide and
other instructions are also available.
To download these drivers and or documentation for
your printer please visitTHIS
PAGE Note that the picture below reads 730, but the actual page linked will be for mp810 1.
Click on Drivers & downloads
2. Select your OS ( Operating system, windows, mac
etc )
3. All available drivers, documents etc will be
available below. For some of the documents a PDF reader may be
required to open and read / print them.
To obtain a PDF reader, read this pagePDF
Documents. Pdf reader(s) Thank you for reading and I hope your printer is
up and running again. -Ekse
Hi You can Try 2 things. ERROR 5100 means that there is some foreign object blocking your cartridges carriage that disables it from moving. Generally when this happens, something has fallen into the printer, or a piece of paper has been jammed in there.
First step, remove the ink cartridge, and turn the printer upside down and gently shake it, see if anything comes out.
If nothing goes, or you can't hear anything rattling around, get a piece of cardstock paper (60lb or heavier) and gently push this through the printer, to see if it will help push out what might be stuck in there Next try. It may be a piece of paper or a scotch tape or a staple wire. Solution 1: Clean the timing strip.
Solution 2: The purge cap (the white sliding mechanism that the print head parks to when it's not in use) may be not lubricated well enough .
Lubricate the sliders with some white grease (don't get it on the small wipers or the black caps); this repair probably require to remove the right panel off of the printer to gain access to the purge mechanism. Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks
Hi
Error 6A00
The 6A00 is a Canon generic code for paper path jam.
Solution 1: Move the printhead carriage back and forth a few times.
Solution 2: Check the purge unit: Moving the print head assembly will not clear a purge unit if its jammed with paper, paper clips, push pins, screws, cookie crisp, flower bud pods or the like.
Solution 3: Press the ink pads down in the purge unit. Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks
Brand new cartridge or refilled one? If refilled cartridge, just wait for 30 minutes after refilling and use good quality of ink. It's caused by bad ink flow. While ink spray (bubbling) form head, ink at ink tank not flow to head.
Hi You can Try
Error Code 5100
Solution 1: Clean the timing strip.
Solution 2: The purge cap (the white sliding mechanism that the print head parks to when it's not in use) may be not lubricated well enough .
Lubricate the sliders with some white grease (don't get it on the small wipers or the black caps); this repair probably require to remove the right panel off of the printer to gain access to the purge mechanism. All The Best: Pineworks
Follow these steps: start off removing the ink tank holder (held in place by the grey lever) and cleaning it with an alcohol solution and paper towel. When the ink tanks are not in use they slide to the right side and rest on a pad that collects excess ink. Mine was loaded up and gel like so I cleaned it as well. With the ink tank removed place your MP600 upside down on the table with a towel underneath to protect the lid, then gave it a few good hits on either side of the lower paper tray.
Duplex printing is only related if the imaged page was not allowed to dry before being re-inserted into the tray.
Was the document blurred? It it was, then ink could have transferred to the rollers.
Since you have cleaned the rollers, then you either have worn rollers or or a worn "Pick" magnet. The tray spring that pushes the tray forward could also be worn.
Oddly enough since you raise the media issue, if you are using "Long Grain" paper as opposed to "Short Grain" paper that could be a source of the problem Short Grain paper allows the page to be more flexible when bending. Long grain paper is stiffer and is tougher to bend.
Its rare that this is a problem but it could happen. Also, make sure you are using paper that is meant for an ink jet printer.
In an ink jet printer, the ink is absorbed into the page, while a laser use heat and pressure to fuse the image onto the top of the page.
Please let me know if this helped you or if you need additional assistance.
this error belongs to carriage jam or mechanism .... my point of view go for a service center and fix it ...if you try you won it may damage your printer
if you want to fix this problem in your own goes through below link may it help you
