20 Most Recent Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum - Page 6 Questions & Answers

0helpful
2answers

Bissell powerforce blows air out at the vent below the bag compartment what causes that ?

There is almost certainly too much resistance somewhere in the machine's air flow. It could be that the filter (if fitted) needs a clean (or even replacing) or the bag/dust reservoir are full. If all ok, check that none of the tubes are blocked. (The air is being forced out of the relief channel due to resistance in the normal 'through flow' of air.)
8/7/2019 4:28:01 PM • Bissell Vacuums • Answered on Aug 07, 2019
0helpful
1answer

My 86t3 Bissell Big Green Machine. Constantly sprays water like Im pressing the trigger. I disconnected the switch for trigger and it still sprays on to the carpet. It will continue to spray until it runs out of water.

I think you should take it to the manufacturer that made this product, so that their maintenance department can have a look at it and fix it.
7/11/2019 8:40:00 AM • Bissell Vacuums • Answered on Jul 11, 2019
0helpful
1answer

My bissell proper fresh steam floor mop just stopped working. It was recommended to me to replace the thermal switch. I have the part but do not see how to make the repair

If the thermal switch is less than the size of a piece of Chicklet chewing gum, it likely mounts either inside the motor, or attaches to the side of the motor. Check on line for a parts diagram. It may help you figure out where the switch goes.
7/11/2019 2:44:28 AM • Bissell Vacuums • Answered on Jul 11, 2019
0helpful
1answer

Bissell Crosswave model 1785F no power

Here's a video tutorial on how to fix it:
https://www.bissell.com/bissell-crosswave-multi-surface-wet-dry-vac-1785/no-power-how-to-videos-crosswave

hope i was able to help
6/16/2019 2:40:40 PM • Bissell Vacuums • Answered on Jun 16, 2019
0helpful
1answer

My Bissell Model 8910-4 Will Not Spray Water Out Of The Floor Nozzles

This is obvious so if you tried this I'm sorry. The nozzles are probably plugged with dirt. Try cleaning the nozzles with a straightened paperclip and wash out the unit.
6/3/2019 5:26:43 PM • Bissell Vacuums • Answered on Jun 03, 2019
0helpful
1answer

My bissell quicksteamer releases water but wont suction

There could be a number of problems, one that the collection tank is not aligned properly. 2. Removable nozzle installed improperly. 3.Removable nozzle full of debris. 4 Red lint screen under collection tank clogged. 5.The collection tank is full. The answer to the first one is: Check tank alignment and secure with side latches. The answer to the second one is Unplug unit. Align two "hooks" into bottom first, then snap into place on top. The answer for third one is:Unplug unit. Remove nozzle and rinse under running water. The solution for 4. is:Remove debris from lint screen. And the solution for 5. is Empty tank
5/24/2019 8:42:14 PM • Bissell Vacuums • Answered on May 24, 2019
0helpful
1answer

The clean water tank does not hold water on my Bissell Revolution.

Have you seated the clean tank properly? That could be the problem.
5/24/2019 8:27:03 PM • Bissell Vacuums • Answered on May 24, 2019
Not finding what you are looking for?
Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum Logo

73 questions posted

Ask a Question

Usually answered in minutes!

Top Bissell Vacuums Experts

Brad Brown

Level 3 Expert

18822 Answers

Mike

Level 3 Expert

4377 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1482 Answers

Are you a Bissell Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Bissell Vacuums

  • Bissell Vacuums

Most Popular Question

attatchment stuck in hose bissell

  • Vacuums
Loading...