20 Most Recent Bissell 1425-1 Little Green ProHeat Canister Wet/Dry Vacuum - Page 2 Questions & Answers

It sounds like the small silver piece that fell out of your BISSELL Powerforce Helix may be the motor brush. The motor brush is a small, spring-loaded carbon block that makes contact with the motor to conduct electricity. If the motor brush falls out or is not installed correctly, it can cause the motor to make a loud, high-pitched noise. To fix the problem, you should locate the motor brush and try to reinstall it. The motor brush is typically located near the motor on one or both sides of the vacuum. You may need to consult the user manual or contact BISSELL customer service for specific instructions on how to access and install the motor brush. If the motor brush is damaged or missing, you may need to purchase a replacement motor brush from BISSELL or a vacuum repair shop. Once you have replaced the motor brush, the high-pitched noise should go away and the vacuum should operate normally.

Replacing the upright locking foot pedal on a Bissell 3760-4 is a fairly straightforward process. Here are the steps you can follow:

1. Turn off and unplug the vacuum cleaner.
2. Lay the vacuum cleaner on its side so that you can access the bottom of the machine.
3. Locate the locking foot pedal and use a screwdriver to remove the screws that hold it in place.
4. Once the screws are removed, gently pull the old locking foot pedal away from the vacuum cleaner.
5. Take the replacement locking foot pedal and position it in the same spot where the old one was removed.
6. Use the screwdriver to attach the replacement locking foot pedal with the screws you removed earlier.
7. Test the new locking foot pedal to make sure it works properly and holds the vacuum cleaner in the upright position.
8. Once you are satisfied with the new locking foot pedal, flip the vacuum cleaner back over to its normal upright position.
9. Plug in the vacuum cleaner and turn it on to make sure everything is functioning properly.

With these steps, you should be able to successfully replace the upright locking foot pedal on your Bissell 3760-4.

switch failure

If the height adjustment on your Bissell PowerForce Helix Turbo Rewind vacuum is not functioning properly, there are a few things you can try to fix it:

1. Make sure that the height adjustment lever is being pressed down all the way. Sometimes the lever can get stuck in the "up" position, which prevents the height adjustment from working.
2. Check the height adjustment mechanism to make sure it is not damaged or obstructed. This may involve removing the vacuum's dustbin or base plate to access the mechanism.
3. If the height adjustment lever and mechanism are functioning properly, the problem could be with the vacuum's belt. The belt is responsible for driving the height adjustment mechanism, and if it is stretched or damaged, it may not be able to move the mechanism properly. In this case, you may need to replace the belt.
4. If none of these solutions fix the problem, the vacuum's internal hardware may be faulty and will need to be repaired or replaced. You may need to seek the assistance of a professional for this type of repair.

If you are having difficulty getting the retainer clip back in place, it may be helpful to check the alignment of the belt and level arms. Make sure that everything is properly aligned and not binding on any other parts. If everything looks aligned but you are still having difficulty, you may need to gently manipulate the brush and belt to get the retainer clip to fit properly. It may also be helpful to refer to the user manual or a guide for your specific model to ensure that you are reassembling the parts correctly. If you are still having difficulty, it may be helpful to seek the assistance of a professional or to contact the manufacturer for further assistanc

It might be the switch, or the motor may have failed. https://www.google.com/search?q=bissell+2230+doesn%27t+turn+on https://www.google.com/search?q=Bissell+2230+parts ..

Question edited for clarity and typos. Did you 'replace the belt 2 times' with a new one? If they stretch, they can come off. https://www.google.com/search?q=belt+on+my+Bissell+Pro-Heat+Shampooer+for+the+pump+keeps+coming+off ..

Check for any clogs in the hose and belt areas

Go to Bissel website: https://www.bissell.com/parts https://www.bissell.com/support I’m happy to help further over the phone at https://www.6ya.com/expert/donald_f2ed37026a3ac881

Question edited for clarity. You can't buy that model new as it is discontinued. For the secondhand market check eBay, or Facebook Marketplace. There does appear to be some old stock available, plus the newer model for $308. eBay has Pre-owned: Lowest price $160.99 + $100.20 Shipping https://www.google.com/search?q=Bissell+9200+price ..

I would look on u tube .

Here is the Service Guide. Plumbing Guide is on Page 22. https://evacuumstore.com/images/proheat-2x-service-guide.pdf ..

https://www.youtube.com/watch?v=afFuV2j3r6w

Either your belt has stretched beyond its specs or you have larger problems. Are you talking about a new belt? If not, try a new belt. If so, check to make sure the beater bar will spin freely without a belt attached. If it spins without a belt attached, make sure the bearing blocks at both ends are in good shape.

It is likely to be similar to the Clean View and Pro Heat. Or take into a Bissell Service Centre. https://www.google.com/search?q=Bissell+Cross+Wave+Pet+Pro+replace+motor ..

You would see if you warped the tank, the issue is most likely related to melting some of the thin pump parts or tubing in the unit. Bissell does not sell those parts to the public. Find a repair center or send it in unless you want to buy a new one. PS in the future don't put high temp water in the tank, put it on the spot you are trying to clean and then vacuum it up.

depends on model thy seem to start around $50.00. I would total parts cost vs new unit. if 50% or more replace.

Not normally, sometimes models have minor differences within the same range. Google make model replacement motor

Yes, the motor has burned out. The motor is here https://www.partswarehouse.com/Bissell-Big-Green-Complete-Deep-Cleaner-Vacuum-7700-s/6667.htm and at other fine emporiums of vacuum heaven. https://www.google.com/search?q=Bissell+Model+%237700+replacement+motor ..

User manuals and videos https://www.google.com/search?q=bissell+little+green+machine+instructions+for+use ..